background image

Building

Type

7

Installation of this tube heater in public garages must conform to the following codes:

 

   United  States:

  Standard for Parking Structures NFPA 88A (latest edition) or the  

 

     Code for Motor Fuel Dispensing Facilities and Repair Garages NFPA 30A (latest  

 

   edition).

   Canada:

  Refer to CAN/CGA B149.1: Installation Codes for Gas Burning Appliances  

    and applicable Standards for Public Garages.

Guidelines:
  •  Heaters must not be installed less than 8 ft. (2.4 m) above the floor. Minimum    

 

    clearances to combustibles must be maintained from vehicles parked below the 

 

   heater.

  • When installed over hoists, minimum clearances to combustibles must be maintained   
    from the upper most point of objects on the hoist.

Installation of this tube heater in aircraft hangars must be in accordance with the 
following codes:

 

   United  States:

 Refer to Standard for Aircraft Hangars, ANSI/NFPA 409  

    (latest edition).

    In Canada:

  Refer to Standard CAN/CGA B149.1 and applicable Standards for  

 

   Aircraft  Hangars.

Guidelines:

  •  In aircraft storage and servicing areas, heaters shall be installed at least 10 ft. (3 m)    
    from above the upper surface of wings or of the engine enclosures of the highest  

 

    aircraft that may be housed in the hangar. The measurement shall be made from the    
    wing or engine enclosure, whichever is higher from the floor, to the bottom of the 
   heater.

  •  In areas adjoining the aircraft storage area (e.g., shops, offices) the bottom of heaters   
    shall be  installed no less than 8 ft. (2.4 m) above the floor.

  •  Suspended or elevated heaters shall be located in spaces where they shall not be  

 

    subject to damage by aircraft, cranes, movable scaffolding or other objects. 

Provisions shall be made to assure accessibility to suspended tube heaters for recurrent 
maintenance purposes.

Standards, Certifications and Government Regulations

Installation of this tube heater must comply with all applicable local, state and national specifications, 
regulations and building codes. Contact the local building inspector and/or fire marshall for guidance. 

In the absence of local codes, the installation must conform to the latest edition of:

 

United States:

   National Fuel Gas Code, ANSI Z223.1 (NFPA 54).

 Canada:

   CAN/CGA B149.1 and .2, Canadian Electrical Code C22.1

Public 

Garages

Aircraft 

Hangars

2.0

 Safety

 

 Standards, Certifications and Government Regulations

Chart 2.1 •

 Standards and Code Installation Guidelines 

 Building Type

Codes and Guidelines

Summary of Contents for heater





































Reviews: