This Manual is applicable to the
Revised April 2nd 2015
De Sisti SOFT LED 4
Pag 6
.
1st MENU
Displayed
(
scrolling with the
Ù
and the
Ú
buttons)
2nd MENU
Displayed
(after pressing the
X
that stands for ENTER)
Explanation of Each MENU FUNCTION
TEMPERATURE
This function Displays in real time the LED BAR Case temperature in °C.
When pressing Enter again you exit from the temperature display.
The steady state TEMPERATURE of the LED BAR reaches approx. 55°C after many hours of
continuous operation with an ambient temperature of 25-30°C.
The Thermal Handling of the LED is Automatically handled by the local electronics and the
LED will operate until the LED BAR temperature reaches 80°C, that anyway is still way within
the prescribed maximum nominal prescribed by the LED BAR manufacturer that is 105°C.
In case the LED BAR temperature reaches 80°C the unit will automatically turn off.
Even in extreme Ambient temperature conditions the LED BAR shall never reach the 80°C
limit.
The above protection threshold is there to protect the LED BAR from stressed working
conditions in case some other failures or specially critical working conditions are causing an
over-temperature.
CHANNEL SETTING (RESOLUTION & FUNCTION)
This Function is to set the DIMMING RESOLUTION either at 8 bits or at 16 bits.
Once CHAN is displayed, act on the
Ù
or
Ú
buttons to scroll through the following
choises:
•
8D: 8 bits resolution (the display will show 8D and this is the default setting).
The Fixture utilises 1 DMX Circuit for the Light Dimming, which is the
BASE CIRCUIT set in the ADDRESS.
•
8DS: NOT ACTIVE (for future use):
The foreseen function for this setting is: 8 bits resolution and STROBE (the display will show 8DS). The
Fixture will utilise 2 DMX Circuits,
the BASE CIRCUIT set in the ADDRESS will be the LIGHT DIMMING
and the second circuit (BASE +1) will be the STROBE
•
16D: 16 bits resolution (the display will show 16D).
The Fixture utilises 2 DMX Circuits,
the BASE CIRCUIT set in the ADDRESS is the Coarse Dimming,
the second Circuit (BASE +1) is the Fine Dimming.
•
16DS: NOT ACTIVE (for future use):
The foreseen function for this setting is: 16 bits resolution and STROBE (the display will show 16DS).
The Fixture will utilise 3 DMX Circuits,
the
BASE CIRCUIT set in the ADDRESS will be the Coarse Dimming,
the second Circuit (BASE + 1) will be the Fine Dimming
.
the third CIRCUIT (BASE + 2) will be the STROBE
Of course the 16 bits function is useful if the corresponding circuits on the DMX LIGHTING
BOARD are also set at 16 bits.
W ARNING : if the LED FRESNEL is set at 16 bits, but more units are having a consecutive
unitary address (for instance first fixture set at Address 1, second fixture set at Address 2 and
so forth, the DM X Channel controlling the Coarse Dimming of the second unit, will also
control the fine dimming of the first unit. In this case it is recommended that all fixtures are
set to 8 bits resolution).
DMX LEVEL
It Shows the DMX Input level on percentage (0-99% and FULL) received effectively from the
Fixture.
Press ENTER to exit this MENU
.
9.
CHARACTERISTICS AND PERFORMANCE DATA
DESCRIPTION
VALUE
DESCRIPTION
VALUE
Ü
LED Power
165 W
Ü
Protection Type
IP 22
Ü
Power
Cosumption
190W @ 230 V (50-60 Hz)
205W @ 120 V (50-60 Hz)
Ü
Max
Housing temperature
70 °C
Ü
DMX Data link
USITT DMX512-A
Ü
This product uses a 5-pin XLR for
DMX input and output.
Ü
Use a shielded data cables.
Ü
Do not overload the daisy chain. Up
to a maximum of 32 devices can be
used on a single DMX chain.
Ü
Weight of Fixture
M.O.
P.O.
8,3 kg.
9,6 kg.
Ü
Weight of Intensifier
kg. 0,476
Ü
DMX
Channels:
Ü
1 at 8bit: Dimmer
Ü
2 at 16bit: Dimmer
Ü
Weight of color frame
kg. 0,275
Ü
Weight of Honeycomb
½
”
Cells (Medium) = 0,424 kg.
¼
”
Cells (Narrow) = 0,376 kg.
Ü
Size & types of Remote
Phosphors Panels
CRI>95
TUNGSTEN
Balanced CCT
CRI>90
DAYLIGHT
Balanced CCT
305 x 140 mm.
305 x 140 mm.
Ü
Protection Class
Class 1– ground connection required
Ü
Front Fixture’s Opening
Front 37,7cm.(base) x 29,1cm. (height) =
surface 1.097 cm
2
Specifications subject to change without notice.
