1.
Remove the original NOX bracket from the NOX fitting. Keep all screws for the following steps.
2.
OPTIONAL - Install the optional ML-PE10 light sensor by sliding the cables through the hole into
the bracket and fix to the side of the bracket using the included screw (A).
3.
Slide the NOX fitting into the new bracket and fix into place using the existing bracket bolts (B2)
on both sides. Ensure you set the correct angle for the NOX and lock it into place using screws (B1).
4.
OPTIONAL - Slide the NOXSPBKT right angle pole adapter into the horizontal bracket (D) and fix
using the included M10 bolts.
5.
OPTIONAL - Slide the NOXSP strait pole spigot adapter into the base of the horizontal bracket
(E) and slightly tension the M10 fixing bolts to hold it into position.
6.
Terminate the input cables to the NOX (including the PE10 if applicable).
7.
Slide the completed unit into place and securely fix the unit into place using included M10 bolts (C)
or other suitable fixings.
8.
Test to ensure compliance and safety.
PLEASE FOLLOW INSTRUCTIONS
FOR CORRECT INSTALLATION:
NOX brackets
ML-NOX3BKT, ML-NOX5BKT, ML-NOX10BKT,
ML-NOX20BKT, ML-NOX30BKT, ML-NOXSP, ML-NOXSPBKT, ML-PE10
Installation instructions
Warranty disclaimer
PLEASE NOTE
•
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
•
All components must not be mechanically stressed
•
Follow all relevant electrical and safety standards (including
AS3000) – only qualified personnel should be allowed to
perform installations
•
Correct electrical polarity needs to be observed as the wrong
polarity may destroy the lights which is not covered under
warranty
•
Damaged by corrosion will not be honoured as a materials
defect claim. It is the user’s responsibility to provide suitable
protection against corrosive agents such as moisture,
condensation and other harmful elements
•
If these regulations are not followed warranty will be void and all
issues are the responsibility of the electrician
•
For further information including photometrics & dimming
range, please visit www.melec.com.au
M-ELEC TRANSFORMERS/DRIVERS
M-Elec provides warranty against defects of
M-Elec drivers
on the following terms and conditions.
Please refer to the M-Elec website (below) for information on the warranty period of each product.
The driver must be properly installed by a qualified electrician and in accordance with our installation
guidelines and any relevant codes and standards.
The warranty does not apply to M-Elec drivers that fail as a result of neglect, mistake, misuse,
alteration, exposure to the elements, or that is improperly installed and implemented.
This includes
but is not limited to: improper wiring, installation under improper and non-approved operating
environments such as temperature, humidity, corrosion or voltage conditions; improper installation
using components that are not approved or are not M-Elec manufactured products.
It is the responsibility of the purchaser to obtain all necessary approvals and to understand the
products intended use and all relevant instructions, recommendations and guidelines for the proper
installation and use of any M-Elec driver product and related ‘manufactured products’ used in
conjunction with same.
M-Elec is not liable for the accuracy and completeness of any statements, technical information and
recommendations in any form of product literature or instructions are not guaranteed and are not part
of this warranty and does not in any way constitute a warranty. The purchaser is solely responsible for
determining suitability of the M-Elec drivers for installation and full implementation must determine
potential applications and installations independently.
To make a claim on this warranty, you must do so within the warranty period (from place of purchase)
please read our returns policy for further information (https://melec.com.au/returns-policy/) and
deliver the driver to M-Elec (at your cost) at the address listed on website. We will assess the warranty
claim and if we grant the warranty claim, we will replace the product or refund your money, at our
election.
M-Elec is not responsible or liable for any injuries, damages, or death caused by the use, misuse or
failure of products purchased from us.
This warranty is in addition to any other rights the consumer
may have under the Australian Consumer Law.
M-ELEC LED PRODUCTS - OTHER
Please refer to the M-Elec website (melec.com.au) for information on the warranty period of each
product. Each of our LED product warranties is separate and subject to the following terms and
conditions:
M-Elec products must be properly installed by a qualified electrician and in accordance with any
relevant guidelines, codes and standards. This includes wiring and connection to proper approved
components and product working environments.
This warranty is void and does not apply to products that fail as a result of neglect, mistake
misuse, alteration, or that is improperly installed and implemented
. This includes but is not limited
to: improper wiring, installation under improper and non-approved operating environments such as
temperature, humidity, corrosion or voltage conditions; improper installation using components that are
not approved or are not M-Elec manufactured products.
It is the responsibility of the purchaser to obtain all necessary approvals and to understand the products
intended use and all relevant instructions, recommendations and guidelines for the proper installation and
use of any M-Elec products and related ‘manufactured products’ used in conjunction with same.
M-Elec is not liable for the accuracy and completeness of any statements, technical information and
recommendations in any form of product literature or instructions are not guaranteed and are not part
of this warranty and does not in any way constitute a warranty. The purchaser is solely responsible
for determining suitability of the M-Elec LED products for installation and full implementation must
determine potential applications and installations independently.
The LED product warranties do not cover LEDs that continue to light, but exhibit varying/differing forward
voltage drops, light output, or colour/wavelength.
Warranty is void if LEDs are cut in any way (outside of LED strip instructions) or damaged by neglect.
Warranty is void if products have been altered, opened/modified in any way that is outside the bounds of
normal electrical work.
Please note:
This does not include removing or hard wiring downlight drivers or the
hard wiring of a flex on an M-Elec flood light.
To make a claim on any of M-Elec’s products, you must do so within the warranty period (from place
of purchase) please read our returns policy for further information (https://melec.com.au/returns-
policy/) and deliver the product to M-Elec (at your cost) at the address listed online. M-Elec will assess
the warranty claim by conducting electrical tests, making sure the contacts still exist on the LED and
visual and microscopic inspection to make sure there is no visible physical damage. If M-Elec grants the
warranty claim, we will replace the product or refund your money, at our election.
M-Elec is not responsible or liable for any injuries, damages, or death caused by the use, misuse or
failure of products purchased from us.
This warranty is in addition to any other rights the consumer may
have under the Australian Consumer Law.
To the fullest extent permitted by law, no warranties other than those described above are given in
respect of M-Elec products. M-Elec’s liability is limited, to the fullest extent permitted by law, to the
refund or replacement of the M-Elec products. We expressly do not warrant that an M-Elec product will
last any particular length of time nor guarantee is made as to fitness to a particular application, since we
have no control of the electrical supply or circuits you are using to drive the LEDs.
M-Elec goods come with guarantees that cannot be excluded under the Australian Consumer Law.
Please read our returns policy procedure for further information on M-Elec website melec.com.au or
request it via phone 1300 222 445 from our customer care consultants.
A
A
B
B
C
C
D
D
E
E
F
F
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:2
SHEET 1 OF 1
A3
WEIGHT:
nox 3 bracket for instructions
E
E
