background image

www.desatech.com

119344-01B

15

6. 

Thermostat  Models:

  Turn  control  knob 

counterclockwise 

  to  the  PILOT 

position. Press in control knob for five (5) 
seconds.

 

Manual Models:

 Press in and turn control 

knob counterclockwise 

 to the PI

-

LOT position. Keep control knob pressed 
in for five (5) seconds.

7.  With control knob pressed in, push down 

and  release  ignitor  button. This  will  light 
pilot. The pilot is attached to the front of 
burner. 

Note:

  You  may  be  running  this 

heater for the first time after hooking up to 
gas supply. If so, you may need to press in 
control knob for 30 seconds or more. This 
will allow air to bleed from the gas system. 
If needed, keep pressing ignitor button until 
pilot lights. If ignitor does not light pilot, re

-

fer to 

Troubleshooting

, page 19 or contact a 

qualified service person or gas supplier for 
repairs. Until repairs are made, light pilot 
with match. To light pilot with match, see 

Manual Lighting Procedure

, page 16.

8.  Keep control knob pressed in for 30 sec

-

onds after lighting pilot. After 30 seconds, 
release control knob.
• If  control  knob  does  not  pop  up  when 

released,  contact  a  qualified  service 
person or gas supplier for repairs.

 

Note:

 If pilot goes out, repeat steps 4 thru 

7. Thermostat models have a safety inter

-

lock system. Wait one (1) minute before 
lighting pilot again.

9.  Turn control knob counterclockwise 

 

to desired heating level. The main burner 
should  light.  Manual  control  heaters 
should be used in locked positions.

oPeRATING HeATeR

FOR YOUR SAFETY READ 

BEFORE LIGHTING

 WARNING: If you do not fol-

low  these  instructions  exactly, 

a  fire  or  explosion  may  result 

causing property damage, per

-

sonal injury or loss of life.

A.  This appliance has a pilot which must 

be lighted by hand. When lighting the pi

-

lot, follow these instructions exactly.

B.  BEFORE  LIGHTING  smell  all  around 

the appliance area for gas. Be sure to 
smell next to the floor because some 
gas is heavier than air and will settle 
on the floor.

 

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do 

not use any phone in your building.

• Immediately  call  your  gas  supplier 

from a neighbor’s phone. Follow the 
gas supplier’s instructions.

• If you cannot reach your gas supplier, 

call the fire department.

C.  Use only your hand to push in or turn 

the gas control knob. Never use tools. 
If the knob will not push in or turn by 
hand, don’t try to repair it, call a qualified 
service technician. Force or attempted 
repair may result in a fire or explosion.

D.  Do  not  use  this  appliance  if  any  part 

has been under water. Immediately call 
a qualified service technician to inspect 
the appliance and to replace any part of 
the control system and any gas control 
which has been under water.

LIGHTING 

INSTRUCTIONS

1.  STOP! Read the safety information above.
2.  Make sure equipment shutoff valve is fully 

open.

3.  Turn off any electric power to the appli

-

ance if service is to be performed.

4.  Turn control knob clockwise 

 to the 

OFF position.

5.  Wait  five  minutes  to  clear  out  any  gas. 

Then  smell  for  gas,  including  near  the 
floor. If you smell gas, STOP! Follow “B” in 
the safety information above. If you don’t 
smell gas, go to the next step.

Figure 19 - Control Knob In The OFF 

Position Manual Control Models

Ignitor Button

Control Knob

OF

F  

  P

ILO

Figure 20 - Control Knob In The OFF 

Position Thermostat Models

Ignitor Button

Control Knob

Summary of Contents for WMN20A





























Reviews: