background image

www.desatech.com

119677-01G

20

CLEANING AND MAINTENANCE

4.  Check injector holder located at the end of 

the burner tube again. Remove any large 

particles of dust, dirt, lint or pet hair with 
a soft cloth or vacuum cleaner nozzle.

5.  Blow air into the primary air holes on the 

injector holder.

6.  In case any large clumps of dust have now 

been pushed into the burner repeat steps 
3 and 4.

Clean pilot assembly also. A yellow tip on the 

pilot flame indicates dust and dirt in the pilot 

assembly. There is a small pilot air inlet hole 

about 2" from where the pilot flame comes out 

of the pilot assembly (see Figure 30). With the 

unit  off,  lightly  blow  air  through  the  air  inlet 

hole. You may blow through a drinking straw 
if compressed air is not available.

Figure 29 - Injector Holder On Outlet 

Burner Tube

Burner 
Tube

Injector Holder

Primary Air 
Inlet Holes

Ports/Slots

Figure 30 - Pilot Inlet Air Hole (Your pilot 

may vary from pilot shown)

Pilot Air 
Inlet Hole

Pilot Assembly

LOGS

•  If  you  remove  logs  for  cleaning,  refer  to 

Installing Logs

, page 16, to properly replace 

logs.

•  Replace log(s) if broken or chipped (dime-

sized or larger).

MAIN BURNER

Periodically inspect all burner flame holes with 
the  heater  running. All  slotted  burner  flame 
holes should be open with yellow flame pres

-

ent. All round burner flame holes should be 
open with a small blue flame present. Some 
burner flame holes may become blocked by 
debris  or  rust,  with  no  flame  present.  If  so, 
turn off heater and let cool. Remove blockage, 
blocked burner flame holes will create soot.

  WARNING:  Turn  off  heater 

and let cool before cleaning.

  CAUTION:  You  must  keep 

control  areas,  burners  and 

circulating  air  passageways 

of  heater  clean.  Inspect  these 

areas of heater before each use. 

Have  heater  inspected  yearly 

by  a  qualified  service  person. 

Heater may need more frequent 

cleaning  due  to  excessive  lint 

from carpeting, pet hair, bedding 

material, etc.

  WARNING:  Failure  to  keep 

the  primary  air  opening(s)  of 

the burner(s) clean may result in 

sooting and property damage.

BURNER INjECTOR HOLDER AND 
PILOT AIR INLET HOLE

The  primary  air  inlet  holes  allow  the  proper 
amount of air to mix with the gas. This provides 

a clean burning flame. Keep these holes clear 
of dust, dirt, lint and pet hair. Clean these air in

-

let holes prior to each heating season. Blocked 
air holes will create soot. We recommend that 
you clean the unit every three months during 
operation and have heater inspected yearly by 

a qualified service person.

We also recommend that you keep the burner 
tube and pilot assembly clean and free of dust 
and dirt. To clean these parts we recommend 
using compressed air no greater than 30 PSI. 

Your local computer store, hardware store or 

home center may carry compressed air in a 

can. If using compressed air in a can, please 

follow the directions on the can. If you don’t 

follow directions on the can, you could dam

-

age the pilot assembly.

1.  Shut off unit, including pilot. Allow unit to 

cool for at least thirty minutes.

2.  Inspect burner, pilot and primary air inlet 

holes on injector holder for dust and dirt 
(see Figure 29).

3.  Blow air through the ports/slots and holes 

in the burner.

Summary of Contents for VUL18NV

































Reviews: