Desa VT32EN Series Owner'S Operation And Installation Manual Download

Page: 1 / 40

For more information, visit www.desatech.com

DIRECT-VENT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

NATURAL GAS “TUDOR” MODEL (V)T32EN SERIES

PROPANE/LP GAS “TUDOR” MODEL (V)T32EP SERIES

WARNING: If the information in this manual is not fol-
lowed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

— Installation and service must be performed by a quali-

fied installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance
CONSUMER: Retain this manual for future reference.

Summary of Contents for VT32EN Series









































Search results

Summary of Contents for VT32EN Series

Reviews:

Related manuals for VT32EN Series

Brands by name

Popular brands

Desa VT32EN Series, Owner'S Operation And Installation Manual

Search results

Summary of Contents for VT32EN Series

Reviews:

Related manuals for VT32EN Series

Brands by name

Popular brands