Desa VT32EN Series Owner'S Operation And Installation Manual Download Page 39

Page: 39 / 40

www.desatech.com

111987-01D

ACCESSORIES

NOTICE: All accessories may

not be available for all fireplace

models.

Purchase these fireplace accessories from your local

retailer. If they can not supply these accessories,

call DESA’s Sales Department at 1-866-672-6040

for information. You can also write to the address

listed on the back page of this manual.

BRICK LINER

(Not Shown)
BL32D -

Refractory Brick Liner Kit

This brick liner adds a touch of style to your direct-

vent fireplace. Complete installation and operation

instructions included in this manual.

FLExIBLE GAS LINE CONNECTOR
GA5081

(Not Shown)

For all models.

pROpANE/NATURAL GAS
CONVERSION KIT

(Not Shown)

PCDE-32T

Propane/LP Gas Conversion Kit

NCDE-32T

Natural Gas Conversion Kit

FACE/LOUVER PANEL KIT

(Not Shown)
RLD32 -

Black Rolled Louver Panels

LOUVER TRIM KIT
(Rolled Louvers Only)

(Not Shown)

LT32B -

Rolled Louver Trim Kit - Brushed

Brass

LT32p -

Rolled Louver Trim Kit - Platinum

LT32PB -

Rolled Louver Trim Kit - Polished

Brass

DEFLECTION HOOD (Not Shown)

HD32

- Hood - Black (" Brow)

PERIMETER TRIM KIT

(Not Shown)

PT32

Perimeter Trim Kit - Black

PT32B

Perimeter Trim Kit - Brushed Brass

PT32P

Perimeter Trim Kit - Platinum

PT32PB

- Perimeter Trim Kit - Polished

Brass

MANUAL BLOWER KIT - BK

Manual variable control blower accessory provides

better heat distribution. Complete installation and

operation instructions included in this manual.

THERMOSTATICALLY-
CONTROLLED BLOWER KIT - BKT

Provides better heat distribution. Blower turns

off and on automatically, as needed. Complete

installation and operation instructions included

in this manual.

REMOTE CONTROL KIT - WRC
SERIES

(Not Shown)

Standard On/Off Electronic Remote
Control Kit

Allows the heater to be turned on and off con

veniently.

Summary of Contents for VT32EN Series









































Search results

Summary of Contents for VT32EN Series

Reviews:

Related manuals for VT32EN Series

Brands by name

Popular brands

Desa VT32EN Series, Owner'S Operation And Installation Manual

Search results

Summary of Contents for VT32EN Series

Reviews:

Related manuals for VT32EN Series

Brands by name

Popular brands