background image

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-
lowed exactly, a fire or explosion may result causing 
property damage, personal injury or loss of life.

—  Do  not  store  or  use  gasoline  or  other  flammable 

vapors and liquids in the vicinity of this or any other 

appliance.

—  WHAT TO DO IF YOU SMELL GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do not use any 

phone in your building.

•  Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire 

department.

—  Installation and service must be performed by a quali-

fied installer, service agency or the gas supplier.

INSTALLER:  Leave  this  manual  with  the  appliance. 
CONSUMER: Retain this manual for future reference.

UNVENTED (VENT-FREE) GAS LOG HEATER

OWNER’S OPERATION AND INSTALLATION MANUAL

24" AND 30" REMOTE-READy MODELS:

VRL24NR, VRL24PR, VRL30NR, VRL30PR, CSG3924NR, 

CSG3924PR, CTB3924NR, CTB3924PR, CSG3930NR, CSG3930PR

24" AND 30" THERMOSTAT MODELS:

VRL24NT, VRL24PT, VRL30NT, VRL30PT, CSG3924NT, CSG3924PT, 

CTB3924NT, CTB3924PT

Remote-Ready Models Also Design-Certified As Vented Decorative Appliances

Summary of Contents for VRL24NR













































Reviews: