background image

www.desatech.com

113061-01F

10

INsTAllATIoN

Continued

Attaching Mounting Bracket To Wall

Note:

 Wall anchors, mounting screws and spacers 

are in hardware package. The hardware package 

is provided with heater.

Attaching To Wall Stud Method

For attaching mounting bracket to wall studs

1.  Drill holes at marked locations using 9/64" 

drill bit.

2.  Place mounting bracket onto wall. Line up last 

hole on each end of bracket with holes drilled 

in wall.

3.  Insert mounting screws through bracket and 

into wall studs.

4.  Tighten  screws  until  mounting  bracket  is 

firmly fastened to wall studs.

Attaching To Wall Anchor Method

For attaching mounting bracket to hollow walls 

(wall areas between studs) or solid walls (concrete 

or masonry)

1.  Drill holes at marked locations using 5/16" 

drill bit. For solid walls (concrete or masonry), 

drill at least 1" deep.

2.  Fold wall anchor as shown in Figure 9.

3.  Insert wall anchor (wings first) into hole. Tap 

anchor flush to wall.

4.  For thin walls (1/2" or less), insert red key 

into wall anchor. Push red key to “pop” open 

anchor wings (see Figure 10). 

IMPORTANT: 

Do not hammer key! For thick walls (over 1/2" 

thick) or solid walls, do not pop open wings.

5.  Place mounting bracket onto wall. Line up 

last hole on each end of bracket with wall 

anchors.

Figure 9 - Folding Anchor

Figure 11 - Mounting Heater Onto 

Mounting Bracket

Stand-
Out Tab

Figure 10 - Popping Open Anchor Wings 

For Thin Walls

Mounting Bracket (attached to wall)

Horizontal Slots

6.  Insert mounting screws through bracket and 

into wall anchors.

7.  Tighten  screws  until  mounting  bracket  is 

firmly fastened to wall.

Placing Heater On Mounting Bracket

1.  Locate two horizontal slots on back panel 

of heater.

2.  Place heater onto mounting bracket. Slide 

horizontal slots onto stand-out tabs on mount

-

ing bracket.

Installing Bottom Mounting Screws

1.  Locate two bottom mounting holes. These 

holes are near bottom on back panel of heater 

(see Figure 12).

2.  Mark screw locations on wall.

3.  Remove heater from mounting bracket.

Figure 12 - Installing Bottom Mounting 

Screws

Side View

Front View

Wall

Spacer

Heater

Summary of Contents for VP20BTA

























Reviews: