background image

www.desatech.com

113111-01D

3

SAFETY INFORMATION

 WARNING: This product con-

tains and/or generates chemicals 

known to the state of California 

to cause cancer or birth defects, 

or other reproductive harm.

IMPORTANT: Read this owner’s 

manual carefully and completely 

before  trying  to  assemble,  op-

erate, or service this fireplace. 

Improper  use  of  this  fireplace 

can cause serious injury or death 

from  burns,  fire,  explosion, 

electrical  shock,  and  carbon 

monoxide poisoning.

 DANGER: Carbon monoxide 

poisoning may lead to death!

Carbon Monoxide Poisoning:

 

Early signs of carbon 

monoxide poisoning resemble the flu, with head-

aches, dizziness, or nausea. If you have these signs, 

the fireplace may not be working properly. 

Get 

fresh air at once!

 Have fireplace serviced. Some 

people are more affected by carbon monoxide than 

others. These include pregnant women, people with 

heart or lung disease or anemia, those under the 

influence of alcohol, and those at high altitudes.

Natural and Propane/LP Gas:

 

Natural and propane/LP 

gases are odorless. An odor-making agent is added 

to these gases. The odor helps you detect a gas leak. 

However, the odor added to the gas can fade. Gas 

may be present even though no odor exists.
Make certain you read and understand all warnings. 

Keep this manual for reference. It is your guide to 

safe and proper operation of this fireplace.

  WARNING:  Any  change  to 

this  heater  or  its  controls  can 

be dangerous.

 WARNING: Do not allow fans 

to blow directly into the fireplace. 

Avoid any drafts that alter burner 

flame patterns. Ceiling fans can 

create  drafts  that  alter  burner 

flame  patterns.  Altered  burner 

patterns can cause sooting.

  WARNING:  Do  not  use  a 

blower  insert,  heat  exchanger 

insert,  or  other  accessory  not 

approved for use with this fire-

place. 

Due  to  high  temperatures,  the 

appliance should be located out 

of traffic and away from furniture 

and draperies.

Do not place clothing or other 

flammable  material  on  or  near 

the appliance. Never place any 

objects in the fireplace.

Fireplace  front  and  screen  be-

come very hot when running fire-

place. Keep children and adults 

away from hot surfaces to avoid 

burns or clothing ignition. Fire-

place will remain hot for a time 

after shutdown. Allow surfaces 

to cool before touching.

Carefully supervise young chil-

dren when they are in the room 

with fireplace.

You must operate this fireplace 

with  the  fireplace  screen  and 

hood  in  place.  Make  sure  fire-

place screen is in place before 

running fireplace.

Keep  the  appliance  area  clear 

and free from combustible ma-

terials, gasoline, and other flam-

mable vapors and liquids.

1.  This appliance is only for use with the type 

of gas indicated on the rating plate. This ap-

pliance is not convertible for use with other 

gases.

2.  Do not place propane/LP supply tank(s) in-

side any structure. Locate propane/LP supply 

tank(s) outdoors (propane/LP only).

Summary of Contents for Vanguard VMH26TNC

































Reviews: