Desa Vanguard VMH26TNA Owner'S Operation And Installation Manual Download Page 13

13

104060

OWNER’S MANUAL

3
2
1

For Built-In Installation

 WARNING: A licensed elec-

trician must connect the wiring
harness to electrical supply fol-
lowing all local codes. Electri-
cian must provide a clamp on
the box cover to secure the wir-
ing. Wiring should be routed
through the bushing in the hole
on the outer casing of heater.

Figure 19 - Installing Blower Bracket Assembly

Blower Bracket
Assembly

Screw

Wire
Harness

Power
Cord

Valve
Cover
Shield

Box Cover

Wire
Harness

Switch Plate

Switch

Clamp Connector
(not included)

Outlet
Receptacle

Blue

Red

INSTALLATION

Continued

Figure 20 - Wiring Diagram For Blower
Accessory Built-In Installation

Extension Cord

Use extension cord if needed. The cord must
have a three-prong, grounding plug and a
three-hole receptacle. Make sure cord is in
good shape. It must be heavy enough to carry
the current needed. An undersized cord will
cause a drop in line voltage. This will result
in loss of power and overheating. Use a No.
16 AWG cord for lengths less than 50 feet.

Follow instructions Removing Valve Cover
Shield 
(page 11), then

1.

Install a snap bushing found in hard-
ware kit into one of the holes found on
rear of valve cover shield. The other
hole is for a strain relief clamp (not
supplied) to secure incoming electrical
supply.

2.

Follow steps 2 through 6 in Installing
Blower Assembly
, pages 11 and 12.
Also remove black wire from middle
switch terminal 2.

3.

Remove black plastic strain relief and
power cord from switch plate. The
power cord supplied will not be used in
built-in installations. Pop in the plastic
snap bushing found in hardware kit into
the hole left by supply cord/strain relief.

4.

A licensed electrician must follow the
wiring diagram to connect incoming
electrical supply to fan kit wiring har-
ness (see Figure 20).

5.

Plug power cord to the outlet receptacle
(not provided) as shown in figure 19.
Wind the extra cable in power cord and
and tie it up with the plastic wire strap
(see Figure 19). Set the cable bundle
between the burner bracket and outer
casing, away from the burner.

6.

Reinstall valve cover shield.

7.

Test to make sure the blower is work-
ing properly.

8.

Reinstall upper louver assembly and
hood if previously removed, (see Figure
15, page 11). Close lower louver door.

Plastic Wire
Strap

Continued

Red

Red

Fan Switch

(Auto/Off/On)

Blue

Blue

Thermostat

Switch

(N.O.)

Green

White

Green

White

On

110/115 

V.A.C.

Blower

Motor

Black 

Off

1

2

3

Auto

Summary of Contents for Vanguard VMH26TNA





























Reviews: