background image

DIRECT-VENT FIREPLACE

®

OWNER’S OPERATION AND INSTALLATION MANUAL

BHDV37NC, BHDV37PC,

BHDV41NC, AND BHDV41PC

Save this manual for future reference.

FOR YOUR SAFETY

WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

• If you cannot reach your gas supplier, call the

fire department.

WARNING: Improper installation,
adjustment, alteration, service, or
maintenance can cause injury or
property damage. Refer to this
manual for correct installation and
operational procedures. For as-
sistance or additional information
consult a qualified installer, ser-
vice agency, or the gas supplier.

This appliance may be installed in an aftermarket* manufactured (mobile) home, where
not prohibited by local codes.

WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury, or
loss of life.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.

— Installation and service must
be performed by a qualified in-
staller, service agency, or the gas
supplier.

— This appliance is only for use
with the type of gas indicated on
the rating plate. This appliance is
not convertible for use with other
gases, unless a certified kit is
used.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.

Summary of Contents for Vanguard BHDV37NC









































Reviews: