Majestic JADE32IN Owner'S Manual Download

Page: 1 / 32

Majestic • JADE32IN, JADE42IN, JADE42IL Owner’s Manual • 2491-987 Rev. F • 9/18

Owner’s Manual

Care and Operation

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

Contact your dealer with questions regarding installation, operation or service.

This appliance may be installed as an OEM

installation in manufactured home (USA

only) or mobile home and must be installed

in accordance with the manufacturer’s

instructions and the

Manufactured Home

Construction and Safety Standard,

Title 24

CFR, Part 3280

in the United States

or the

Standard for Installation in Mobile Homes,

CAN/CSA Z240 MH Series,

in Canada.

This appliance is only for use with the type(s)

of gas indicated on the rating plate. This

appliance is not convertible for use with other

gases, unless a certified kit is used.

In the Commonwealth of Massachusetts installation must be

performed by a licensed plumber or gas fitter.

See appliance installation manual for additional

Commonwealth of Massachusetts requirements.

DANGER

HOT GLASS

WILL

CAUSE BURNS.

DO NOT TOUCH

GLASS

UNTIL COOLED.

NEVER

ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of

burns from the hot viewing glass is provided

with this appliance and shall be installed for

the protection of children and other at-risk

individuals.

•

DO NOT

store or use gasoline or other flam

mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

DO NOT

try to light any appliance.

DO NOT

touch any electrical switch.

NOT

use any phone in your building.

- Leave the building immediately.
- Immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier’s instructions.

- If you cannot reach your gas supplier, call

the fire department.

• Installation and service must be performed

by a qualified installer, service agency, or the

gas supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

NOTICE: DO NOT

discard this manual!

Models:

JADE32IN

JADE42IN

JADE42IL

Summary of Contents for JADE32IN

































Search results

Summary of Contents for JADE32IN

Reviews:

Related manuals for JADE32IN

Brands by name

Popular brands

Majestic JADE32IN, Owner'S Manual

Search results

Summary of Contents for JADE32IN

Reviews:

Related manuals for JADE32IN

Brands by name

Popular brands