background image

7

099241

www.desatech.com

5. Squeeze trigger to fire.
6.

IMPORTANT:

 Do not fire this tool

when empty of staples. This may
damage tool.

Note:

 In difficult fastening jobs, press

down on head of tool with palm of free
hand (see Figure 6). This will improve
staple driving.

Tool Jam
1. If tool jams, move trigger lock to the OFF position and unplug tool.
2. Turn tool upside down.
3. Press in latch lock and slide staple chamber cover back until fully open.
4. Remove unused staples.
5. Remove staple(s) causing jam.
6. Reload tool (see Loading Tool, page 5).

Cleaning

Use a clean cloth to remove dirt from tool. Do not use solvents when cleaning
plastic parts.

Lubrication

Do not oil or grease any part of tool. This may damage tool.

IMPORTANT:

 Do not attempt to repair tool or replace broken parts.

Figure 6

Maintenance

 WARNING: Do not alter this tool in any way. Only use accessories

designed for this tool.

 WARNING: Never perform steps listed below while tool is plugged

in. Accidental discharge may occur. Move trigger lock to the OFF
position and unplug tool.

Summary of Contents for PowerFast 34392

























Reviews:

Related manuals for PowerFast 34392