background image

IMPORTANT:  Read  and  understand  this  manual 

before  assembling,  starting  or  servicing  this 

product.  When  using  electrical  products,  basic 

safety precautions should always be followed to 

reduce the risk of fire, electric shock and injury to 

persons. Keep this manual for future reference.

Save this manual for future reference.

For more information, visit www.desatech.com

MODELS PD15EA, PG15EA, PL15EA AND PV15EA

1500 WATT  120V 60HZ  12.5 AMPS

OUTDOOR ELECTRIC PATIO TABLE UMBRELLA STAND AND 

FOOT WARMER SERVICE MANUAL

TABLE OF CONTENTS

Safety Information ............................................... 2
Pre-Operating Instructions .................................. 3
General Information ............................................. 4
Product Identification ........................................... 5
Installation ........................................................... 5
Operation ............................................................. 5
Cleaning .............................................................. 5

Wiring Diagram .................................................... 5
Safety Requirements ........................................... 6
Cautions .............................................................. 6
All Systems Working Together ............................. 6
Troubleshooting ................................................... 6
Reassembly Points .............................................. 8
Illustrated Parts Breakdown and Parts List ....... 10

Summary of Contents for PD15EA













Reviews: