Desa M125TH Owner'S Manual Download Page 12

Page: 12 / 20

112865-01A

For more information, visit www.desatech.com

IGNITION CONTROL ASSEMBLY

WARNING: High voltage!

Fuse

Fuse Cover

Fuse Clips

Unplug heater.

Remove control cover screws (2) using phillips screwdriver to
expose ignition control assembly (see Figure 11, page 9).

Remove fuse cover.

Remove fuse from fuse clips.

Replace with new fuse (DESA Heating Products part number
105880-02). Do not substitute a fuse with a higher current rat-
ing. Use Bussmann GMA-10 or equivalent.

Replace fuse cover.

Replace control cover (see Figure 11, page 9).

PUMP ROTOR

(Procedure if Rotor is Binding)

Remove upper shell (see Upper Shell Removal, page 8).

Remove fan guard.

Remove filter end cover screws using 5/16" nut driver (see
Figure 18).

Remove filter end cover and air filters.

Remove pump plate screws using 5/16" nut-driver.

Remove pump plate.

Remove rotor, insert, and blades (see Figure 18).

Check for debris in pump. If debris is found, blow out with
compressed air.

Install insert and rotor.

10. Check gap on rotor. Adjust to .003"/.004" (.076/.101 mm) if

needed (see Figure 19).

Note:

Rotate rotor one full turn to ensure the gap is .003"/.004"

(.076/.101 mm) at tightest position. Adjust if needed.

11. Install blades, pump plate, air filters, and filter end cover.

12. Replace fan guard and upper shell (see Upper Shell Removal,

page 8).

13. Adjust pump pressure (see Pump Pressure Adjustment, page 9).

Note:

If rotor is still binding, proceed as follows.

SERVICE PROCEDURES

Continued

Figure 18 - Rotor Location

Insert

Blade

Rotor

Pump Plate

Air Intake
Filter

Air Output
Filter

Filter End
Cover

Gap Adjusting Screw

Rotor

Blade

.003"/.004"
(.076-.101 mm)
Gap Measured
With Feeler
Gauge

Gap Adjusting Screw
Figure 19 - Gap Adjusting Screw Locations

Sandpaper

Figure 20 - Sanding Rotor

SERVICE PROCEDURES

Figure 21 - Replacing Fuse

14. Perform steps 1 through 6.

15. Place fine grade sandpaper (600 grit) on flat surface. Sand ro-

tor lightly in “figure 8” motion four times (see Figure 20).

16. Reinstall insert and rotor.

17. Perform steps 10 through 12.

Summary of Contents for M125TH





















Search results

Summary of Contents for M125TH

Reviews:

Related manuals for M125TH

Brands by name

Popular brands

Desa M125TH, Owner'S Manual

Search results

Summary of Contents for M125TH

Reviews:

Related manuals for M125TH

Brands by name

Popular brands