background image

www.ironhaus.com or www.desatech.com

121333-01A

36

TRoUbLeShooTING

Continued

 WARNING: If you smell gas

•  Shut off gas supply.

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not use any phone in your 

building.

•  Immediately call your gas supplier from a neighbor’s phone. Fol

-

low the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire department.

pOSSIBLE CAUSE

1. Gas  leak. 

See  Warning 

statement above 

1. High or gusting winds

2. Low line pressure

3. Pilot is partially clogged

4. Inner vent pipe leaking ex-

haust gasses into system

5. Glass  too  loose  and  air 

tight gasket leaks in cor-
ners after usage

6. Bad thermopile or thermo-

couple

7. Improper vent cap instal-

lation

1. Gas  leak. 

See  Warning 

statement above 

2. Control valve defective

1. Gas  leak. 

See  Warning 

statement above

OBSERVED PROBLEM

Fireplace  produces  un-
wanted odors

Fireplace shuts off in use 

Gas odor even when control 
knob is in OFF position

Gas odor during combustion

REMEDY

1. Locate  and  correct  all  leaks 

(see 

Checking  Gas  Connec-

tions

, page 23)

1. Fireplace  has  been  tested  for 

up to 40 mph winds. However, 
extreme conditions may occur. 
See 

Lighting  Instructions

  on 

page 28

2. Contact  local  propane/LP  or 

natural gas company

3. Clean pilot (see 

Cleaning and 

Maintenance, 

page 31)

4. Locate  and  correct  all  leaks 

(see 

Checking  Gas  Connec-

tions

, page 23)

5. Tighten glass

6. Replace faulty component

7. Check  for  proper  installation 

and  freedom  from  debris  or 
blockage

1. Locate  and  correct  all  leaks 

(see 

Checking  Gas  Connec-

tions

, page 23)

2. Replace control valve

1. Locate  and  correct  all  leaks 

(see 

Checking  Gas  Connec-

tions

, page 23)

Summary of Contents for Ironhaus Selway IKC36N Series













































Reviews: