background image

www.desatech.com

119421-01E

17

OPERATION

 LIGHTInG 

InSTRUCTIOnS 

 WARnInG

•  If  fireplace  has  glass  doors, 

never operate this heater with 

glass doors closed. If you op-

erate heater with doors closed, 

heat  buildup  inside  fireplace 

will cause glass to burst. Make 

sure there are no obstructions 

across openings of fireplace.

•  You must operate this heater 

with  a  fireplace  screen  in 

place.  Make  sure  fireplace 

screen  is  closed  before  run-

ning heater.

NOTICE: During initial operation 

of new heater, burning logs will 

give off a paper-burning smell. 

Orange flame will also be pres-

ent. Open damper or window to 

vent smell. This will only last a 

few hours.

Note: Home owners generally prefer to oper-
ate  their  heater  with  the  chimney  damper 
closed. This will put all the heat into the room. 
However, there may be times you will desire 

the full flames of the HI heat setting but will 
find the heat output excessive. You can open 

the chimney damper (if you have one) fully or 
partially to release some of the heat.

 WARNING: Damper handle 

will  be  hot  if  heater  has  been 

running.

1.  STOP!  Read  the  safety  information  in 

column 1.

2.  Make sure equipment shutoff valve is fully 

open.

3.  Press in and turn control knob clockwise 

 to the OFF position.

4.  Wait five (5) minutes to clear out any gas. 

Then  smell  for  gas,  including  near  the 
floor. If you smell gas, STOP! Follow “B” 
in the safety information, column 1. If you 
don’t smell gas, go to the next step.

FOR YOUR SAFETY 

READ BEFORE LIGHTING 

 WARNING: If you do not fol-

low these instructions exactly, 

a  fire  or  explosion  may  result 

causing property damage, per-

sonal injury or loss of life.

A.  This appliance has a pilot which must 

be  lighted  by  hand.  When  lighting 
the  pilot,  follow  these  instructions 
exactly.

B.  BEFORE  LIGHTING  smell  all  around 

the appliance area for gas. Be sure to 
smell next to the floor because some 
gas is heavier than air and will settle 
on the floor.

 

WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do 

not use any phone in your building.

• Immediately  call  your  gas  supplier 

from a neighbor’s phone. Follow the 
gas supplier’s instructions.

• If you cannot reach your gas supplier, 

call the fire department.

C.  Use only your hand to push in or turn 

the gas control knob. Never use tools. 
If the knob will not push in or turn by 
hand, don’t try to repair it, call a quali-
fied service technician or gas supplier. 
Force or attempted repair may result in 
a fire or explosion.

D.  Do not use this appliance if any part 

has  been  under  water.  Immediately 
call  a  qualified  service  technician  to 
inspect  the  appliance  and  to  replace 
any  part  of  the  control  system  and 
any gas control which has been under 
water.

Summary of Contents for HDVF3018N





























Reviews: