background image

www.desatech.com

119421-01E

13

INSTALLATION

Continued

Figure 12 - Attaching Base Assembly to 

Fireplace Floor - Dual Burner Model

Masonry 

Screw

Mounting 
Bracket

COnnECTInG TO GAS SUppLY

  WARNING:  This  appliance 

requires  a  1/2"  NPT  (National 

Pipe Thread) inlet connection to 

the pressure regulator.

 WARNING: A qualified service 

person must connect heater to gas 

supply. Follow all local codes.

 CAUTION: Never connect heater 

directly to the propane/LP supply. 

This  heater  requires  an  external 

regulator  (not  supplied).  Install 

the external regulator between the 

heater and propane/LP supply.

 WARNING: Never connect 

natural gas fireplace to private 

(non-utility)  gas  wells.  This 

gas  is  commonly  known  as 

wellhead gas.

Installation Items Needed

Before installing heater, make sure you have 
the items listed below.
•  external regulator (supplied by installer)
•  piping (check local codes)
•  sealant (resistant to propane/LP gas)
•  equipment shutoff valve *
•  test gauge connection *
•  sediment trap
•  tee joint
•  pipe wrench
* A  CSA  design-certified  equipment  shutoff 
valve with 1/8" NPT tap is an acceptable al

-

ternative to test gauge connection. Purchase 

the optional CSA design-certified equipment 

shutoff valve from your dealer.

For  propane/LP  units,  the  installer  must 

supply  an  external  regulator.  The  external 

regulator will reduce incoming gas pressure. 
You must reduce incoming gas pressure to 
between 11" and 14" of water. If you do not re

-

duce incoming gas pressure, heater regulator 

damage could occur. Install external regulator 

with the vent pointing down as shown in Figure 
13.  Pointing  the  vent  down  protects  it  from 
freezing rain or sleet.

  CAUTION:  Use  only  new, 

black  iron  or  steel  pipe.  Inter-

nally-tinned copper tubing may 

be used in certain areas. Check 

your  local  codes.  Use  pipe  of 

1/2" diameter or greater to allow 

proper gas volume to heater. If 

pipe is too small, undue loss of 

volume will occur.

Figure 13 - External Regulator With Vent 

Pointing Down

Propane/LP 
Supply Tank

External 
Regulator 

with Vent 

Pointing 

Down

7.  Mark  screw  locations  through  holes  in 

mounting  brackets  (see  Figure  12).  If 

installing in a brick-bottom fireplace, mark 
screw locations in mortar joint of bricks.

8.  Remove heater base from fireplace.
9.  Drill holes at marked locations using 3/16" 

drill bit.

10. Attach  base  assembly  to  fireplace  floor 

using two masonry screws (in hardware 

package) (see Figure 12).

Summary of Contents for HDVF3018N





























Reviews: