background image

www.desatech.com

121353-01F

24

AUTO

OFF

ON

Thermopile

TROUbLESHOOTING

 WARNING: Turn off heater and let cool before servicing. Only a 

qualified service person should service and repair heater.

 CAUTION: Never use a wire, needle, or similar object to clean 

ODS/pilot. This can damage ODS/pilot unit.

Note: All troubleshooting items are listed in order of operation.

OBSERVED PROBLEM

When ignitor button is pressed, 

there  is  no  spark  at  ODS/
pilot

When ignitor button is pressed, 

there is spark at ODS/pilot but 
no ignition

POSSIBLE CAUSE

1. Ignitor  electrode  not  con-

nected to ignitor cable

2. Ignitor  cable  pinched  or 

wet

3. Piezo ignitor nut is loose

4. Broken ignitor cable

5. Bad piezo ignitor

6. Ignitor electrode broken
7. Ignitor electrode positioned 

wrong

1. Gas  supply  turned  off  or 

equipment  shutoff  valve 

closed

2. Control knob not in PILOT 

position

3. Control knob not pressed in 

while in PILOT position

4. Air  in  gas  lines  when  in

-

stalled

5. Depleted gas supply (pro-

pane/LP gas)

6. ODS/pilot is clogged

7. Gas regulator setting is not 

correct

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if pinched 

by  any  metal  or  tubing. 

Keep ignitor cable dry

3. Tighten  nut  holding  piezo 

ignitor to base panel of log 
set.  Nut  is  located  behind 
base panel

4. Replace ignitor cable

5. Replace piezo ignitor

6. Replace pilot assembly
7. Replace pilot assembly

1. Turn on gas supply or open 

equipment shutoff valve

2. Turn control knob to PILOT 

position

3. Press in control knob while 

in PILOT position

4. Continue  holding  down 

control knob. Repeat ignit-
ing  operation  until  air  is 
removed

5.  Contact  local  propane/LP 

gas company

6. Clean  ODS/pilot  (see 

Cleaning and Maintenance, 

page 23) or replace ODS/
pilot assembly

7. Replace gas control

WIRING DIAGRAM

Note: For proper operation of optional acces-
sories, the wires from the switch to the control 
must be connected exactly as shown.

Summary of Contents for FLAME-MAX VYM27NR

































Reviews: