![background image](http://html1.mh-extra.com/html/desa/comfort-glow-cgcf26nr/comfort-glow-cgcf26nr_owners-operation-and-installation-manual_2486308014.webp)
14
104326
VENT-FREE NATURAL GAS COMPACT FIREPLACE
CGCF26NR
O
F
F
PIL
OT
O
N
LO
IH
REMOTE
OFF
ON
LIGHTING
INSTRUCTIONS
1.
STOP! Read the safety information,
column 1.
2.
Make sure manual shutoff valve is
fully open.
3.
Set remote selector switch in the OFF
position.
NOTICE: During initial operation
of new fireplace, burning logs
will give off a paper-burning
smell. Orange flame will also be
present. Open window to vent
smell. Operate fireplace on HI
position to burn off odor. This
will only last a few hours.
WARNING: You must operate
this heater with a fireplace screen
in place. Make sure fireplace
screen is installed before run-
ning heater.
WARNING: Burners will come
on automatically within one
minute when the remote selector
switch is in the ON position after
the pilot is lit.
CAUTION: Do not try to adjust
heating levels by using the
manual shutoff valve.
Control Knob
Ignitor Button
Selector
Switch in
OFF
Position
Flame Adjustment Knob
Figure 23 - Control Knob and Ignitor Button Location
Figure 24- Pilot
Ignitor
Electrode
Pilot Burner
WARNING: Make sure the
remote selector switch is in the
OFF position when you are away
from home for long periods of
time. Heater will come on auto-
matically with remote selector
switch in the ON position.
4.
Press in and turn control knob clock-
wise
to the OFF position.
5.
Wait five (5) minutes to clear out any
gas. Then smell for gas, including
near the floor. If you smell gas,
STOP! Follow “B” in the safety in-
formation, column 1. If you don’t
smell gas, go to the next step.
6.
Press in and turn control knob coun-
terclockwise
to the PILOT
position. Press in control knob for
five (5) seconds (see above).
Note:
You may be running this
heater for the first time after hook-
ing up to gas supply. If so, the con-
trol knob may need to be pressed in
for 30 seconds or more. This will al-
low air to bleed from the gas system.
7.
With control knob pressed in, press
and release ignitor button. This will
light pilot. The pilot is attached to the
front burner. If needed, keep press-
ing ignitor button until pilot lights.
Note:
If pilot does not stay lit, con-
tact a qualified service person or gas
supplier for repairs. Until repairs are
made, light pilot with match. To light
pilot with match, see Manual Light-
ing Procedure on page 15.
8.
Keep control knob pressed in for 30
seconds after lighting pilot. After 30
seconds, release control knob.
• If control knob does not pop out
when released, contact a qualified
service person or gas supplier for
repairs.
Note:
If pilot goes out, repeat steps
4 through 8.
9.
Slightly push in and turn control
knob counterclockwise
to the
ON position.
10. Wait one minute and switch remote
selector switch to the ON position to
light burner.
11. Set flame adjustment knob to any
level between HI and LO.
OPERATING
FIREPLACE
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not fol-
low these instructions exactly, a
fire or explosion may result caus-
ing property damage, personal
injury or loss of life.
A. This appliance has a pilot which must
be lighted by hand. When lighting the
pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas sup-
plier, call the fire department.
C. Use only your hand to push in or turn
the gas control knob. Never use tools.
If the knob will not push in or turn
by hand, don’t try to repair it, call a
qualified service technician or gas
supplier. Force or attempted repair
may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been un-
der water.