manualshive.com logo in svg

Desa Comfort Glow CCL3018NTA, Owner'S Operation And Installation Manual

Share
Download
Desa Comfort Glow CCL3018NTA Owner'S Operation And Installation Manual Download Page 35

www.desatech.com

113097-01L

35

PARTS

VARIABLE MANUALLY-CONTROLLED SEASONAL OAK MODELS

This  list  contains  replaceable  parts  used  in  your  heater.  When  ordering  parts,  follow  the 

instructions listed under 

Replacement Parts, 

below.

KEY 
NO.

PART NUMBER

DESCRIPTION

QTY.

CRL2718PA CRL2718NA CRL3124PA CRL3124NA

1

113551-01 113551-01 113551-02 113551-02 Back Log (#1)

1

2

113552-01 113552-01 113552-02 113552-02 Front Log (#2)

1

3A 113553-01 113553-01 113553-01 113553-01 Left Crossover Log (#3A)

1

3B 113554-01 113554-01 113554-01 113554-01 Right Crossover Log (#3B)

1

4

**

**

**

**

Painted Base Assy

1

5

102844-01 102844-01 102844-01 102844-01

Lower Bracket

1

6

M11084-38 M11084-38 M11084-38 M11084-38

Screw, Hex Head (#8-18 x 0.38)

8

7

098867-10 098867-14 098867-10 098867-14 Gas Regulator

1

8

111331-04 111331-04 111331-04 111331-04 Outlet Burner Tube

1

9

102798-01 102798-01 102798-01 102798-01 Inlet Tube

1

10

099056-21 099056-20 099056-19 099056-18

Burner Orifice Injector

1

11

111124-01 111124-01 111124-01 111124-01 Burner Retainer Spring

1

12

102963-02 102963-02 102773-03 102773-03 Burner

1

13

119583-01 102568-07 119583-01 102568-07 Control Valve

1

14

098508-01 098508-01 098508-01 098508-01 Valve Retainer Nut

1

15

098354-01 098354-01 098354-01 098354-01

Control Knob

1

16

102445-01 102445-01 102445-01 102445-01

Piezo Ignitor

1

17

098249-01 098249-01 098249-01 098249-01

Nut, M5

2

18

099387-08 099387-08 099387-08 099387-08 Pilot Tube

1

19

098271-10 098271-10 098271-10 098271-10 Ignitor Cable

1

20

PP224

PP224

PP224

PP224

ODS Pilot

1

21

PP229

PP229

PP229

PP229

Hex Head Plug, 1/8" NPT

1

PARTS AVAILABLE — NOT SHOWN

100563-01 100563-01 100563-01 100563-01 Warning Plate

1

101055-02 101055-02 101055-02 101055-02 Lighting Instructions Plate

1

100565-01 100565-01 100565-01 100565-01 Warning Plate Fastener 

1

100639-01 100639-01 100639-01 100639-01 Caution Decal

1

101449-04 101449-04 101449-04 101449-04 Control Position Decal

1

101137-02 101137-02 101137-02 101137-02

Hardware Kit

1

GA6060

GA6060

GA6060

GA6060

Lava Rock

1

** Not a field replaceable part.

REPLACEMENT PARTS

Note:  Use  only  original  replacement  parts. 
This will protect your warranty coverage for 
parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If 
they can’t supply original replacement part(s), 
call DESA Heating, LLC at 1-866-672-6040.
When calling DESA Heating, LLC, have ready:
•  your name
•  your address
•  model and serial numbers of your heater
•  how heater was malfunctioning
•  purchase date

Usually, we will ask you to return the part to 

the factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. 

If  they  can’t  supply  original  replacement 

part(s),  either  contact  your  nearest 

Parts 

Central

 (see page 31) or call DESA Heating, 

LLC at 1-866-672-6040 for referral informa-

tion. A list of authorized dealers can be found 

by visiting 

www.desatech.com.

When calling DESA Heating, LLC, have ready:
•  model and serial numbers of your heater
•  the replacement part number

Summary of Contents for Comfort Glow CCL3018NTA





































Reviews:

No comments

Brands by name

Popular brands

Load more brands