background image

12

101809

18 3/4"

Min.

11"

Min.

16"

18 3/4"

Min.

7 1/4"

Min.

Adjoining Wall

16"

Adjoining Wall

Only Insert Mounting 

Screws Through Last 

Hole On Each End

Only Insert Mounting 

Screws Through Last 

Hole On Each End

Floor

Floor

Marking Screw Locations

1. Tape mounting bracket to wall where heater will be located. Make sure mount-

ing bracket is level.

Attaching Mounting Bracket To Wall
Note: 

Wall anchors, mounting screws, and spacers are in hardware package. The

hardware package is provided with heater.

Attaching to wall stud method

For attaching mounting bracket to wall studs
1. Drill holes at marked locations using 9/64" drill bit.
2. Place mounting bracket onto wall. Line up last hole on each end of bracket with

holes drilled in wall.

3. Insert mounting screws through bracket and into wall studs.
4. Tighten screws until mounting bracket is firmly fastened to wall studs.

Attaching to wall anchor method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid
walls (concrete or masonry)
1. Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or

masonry), drill at least 1" deep.

2. Fold wall anchor as shown in Figure 9.

Model VN2800BTB and

CFN2800BTB

Models VN2000BTB and

CFN2000BTB

Figure 8 - Mounting Bracket Clearances

2. Mark screw locations on wall (see Figure 8).

Note: 

Only mark last hole on each end of mounting bracket. Insert mounting

screws through these holes only.

3. Remove tape and mounting bracket from wall.

3. Insert wall anchor (wings first) into hole. Tap anchor flush to wall.

Figure 9 - Folding Anchor

WARNING ICON

G 001

 WARNING

Maintain minimum clearances shown in Figure 8. If you can,
provide greater clearances from floor and joining wall.

INSTALLING TO

WALL

Continued

Summary of Contents for CFN2000BTB

































Reviews: