background image

21

102653

INSTALLING

Continued

 WARNING

Failure to position the parts in accordance with these diagrams or failure
to use only parts specifically approved with this heater may result in
property damage or personal injury.

INSTALLING LOGS (Split Oak Design Models)

Bottom Middle Log (#2)

Metal Post

Metal Post

Peg

Groove

Groove

Grate

Each log is marked with a number. These numbers will help you identify the log when
installing. It is very important to install these logs exactly as instructed. Do not modify
logs. Only use logs supplied with heater.

1. Place front logs (#1L and #1R) on top of the grate. Make sure the notches in the bottom

of the logs fit over the grate prongs (see Figure 22). Push back of logs flush with metal
grate bar.  

Note:

 

18" model has only one front log.

2. Rest bottom middle log (#2) behind metal posts on front burner. Make sure the grooves in

the bottom of the log fit over the grate. Bring the log forward next to the metal posts. The
pegs on the log must be on top (see Figure 23).

3. Slide the grooves in the back of the rear log (#3) against the rear grate prongs. Make

sure the peg on the log is on top (see Figure 24).

4. Place the top middle log (#4) on the bottom middle log (#2). Make sure the pegs of the

bottom middle log fit securely in the holes of the top middle log (see Figure 25).

Figure 22 - Installing Front Logs

(#1L and #1R)

Grate
Prongs

Metal Grate Bar

Front Log (#1L)

Notch

Front Log (#1R)

Figure 23 - Installing Bottom

Middle Log (#2)

Rear Log (#3)

Peg

Grate
Prong

Grate
Prong

Rear
Burner

Groove
in Back
of Log

Groove
in Back
of Log

Figure 24 - Installing Rear Log (#3)

Top Middle Log (#4)

Hole

Peg

Peg

Bottom
Middle Log

Figure 25 - Installing Top Log (#4)

Continued

Hole

Summary of Contents for CF18PV













































Reviews: