background image

www.desatech.com

5

113183-01B

PRODUCT 

IDENTIFICATION

Log Set 

Base 
Assembly

Ignitor

Burner 
Control Knob

Figure 1 - Product Identification

Grate

UNPACKING

 CAUTION: Do not remove the  

data  plates  from  the  base  as-

sembly. The data plates contain 

important  warranty  and  safety 

information.

1.  Remove logs and heater base assembly from 

carton. 

Note:

 Do not pick up heater base as-

sembly by burners. This could damage heater. 

Always handle base assembly by the sides of 

assembly. 

2.  Remove all protective packaging applied to 

logs and heater for shipment.

3.  Check all items for any shipping damage. If 

damaged, promptly inform dealer where you 

bought heater.

PRODUCT FEATURES

OPERATION

This heater is clean burning. It requires no outside 

venting. There is no heat loss out a vent or up a 

chimney. Heat is generated by both realistic flames 

and glowing coals. This heater is designed for vent-

free operation with flue damper closed. It has been 

tested and approved to ANSI Z21.11.2 standard for 

unvented heaters. State and local codes in some 

areas prohibit the use of vent-free heaters.

SAFETY DEVICE

This heater has a pilot with an Oxygen Deple-

tion Sensing (ODS) safety shutoff system. The 

ODS/pilot is a required feature for vent-free room 

heaters. The ODS/pilot shuts off the heater if there 

is not enough fresh air.

IGNITION SYSTEM

This heater has an electronic ignitor to light heater 

fuel supply.

AIR FOR COMBUSTION 

AND VENTILATION

 WARNING: This heater shall 

not  be  installed  in  a  confined 

space or unusually tight construc-

tion unless provisions are provid-

ed for adequate combustion and 

ventilation air. Read the following 

instructions to insure proper fresh 

air for this and other fuel-burning 

appliances in your home. 

Todayʼs homes are built more energy efficient 

than ever. New materials, increased insulation and 

new construction methods help reduce heat loss 

in homes. Home owners weather strip and caulk 

around windows and doors to keep the cold air out 

and the warm air in. During heating months, home 

owners want their homes as airtight as possible.
While it is good to make your home energy effi-

cient, your home needs to breathe. Fresh air must 

enter your home. All fuel-burning appliances need 

fresh air for proper combustion and ventilation.
Exhaust fans, fireplaces, clothes dryers and fuel 

burning appliances draw air from the house to 

operate. You must provide adequate fresh air for 

these appliances. This will insure proper venting 

of vented fuel-burning appliances.

PROVIDING ADEQUATE 
VENTILATION 

The following are excerpts from 

National Fuel 

Gas Code, ANSI Z223.1/NFPA 54, Section 5.3, 

Air for Combustion and Ventilation.

All spaces in homes fall into one of the three fol-

lowing ventilation classifications:
1.  Unusually Tight Construction
2.  Unconfined Space
3.  Confined Space
The information on pages 5 through 7 will help 

you  classify  your  space  and  provide  adequate 

ventilation. 

Summary of Contents for CDR3924NT





























Reviews: