background image

 

 

 

 

www.deponti.com                  Assembly Manual 

– Pinela Deluxe Pergola                     page

 

 

 

29 

7.3 Programming of the lights (optional) 

 of 

 

Step 8: 

In order to set front limit, press 

UP

 and 

MY

 button constantly. The panels will open. When 

the panels reach the middle of the projection press 

MY 

button. 

 

Front limit position defined.  

 
Step 9: 

Press again the 

MY 

button. 

Step 10: 

Press PROG button on your transmitter. 

 

 

Step 1: 

Choose the channel on your transmitter that you want to set the lights. 

Step 2:

 Provide power to lighting control box. (The lights will blink) 

Step 3: 

Press and hold the UP and DOWN button on your transmitter until the lights will jog. 

Step 4: 

Press and hold the programming button of the transmitter, until the lights will jog again. 

  The lights has stored to desired channel on your transmitter. 

 
Deleting of the motor or lights (Perimeter Lights) 

Step 1: 

turn off to power for 2 sec. 

Step 2:

 Turn on to power for 10 sec. 

Step 3:

 Turn off to power for 2 sec. 

Step 4:

 Turn on to power, after that motor or lights will go on 

Step 5:

 Press the programming button on your transmitter. 

  The motor or lights have been deleted on your transmitter. 

 

 

Summary of Contents for Pinela Deluxe
































Reviews: