background image

2

ROTARY HAMMER

EN

PROPER USAGE AND GENERAL INFORMATION

Electrical Rotary Hammer is designed for hammer drilling in bricks, concrete and rocks and also for drilling into 
different constructional materials.
 The tool is designed for usage at the environment temperature from 0 °С  to +40 °С , relative humidity not more than 
80% and absence of direct exposure of atmospheric condensation and excessive air dustiness.
Rotary Hammer is suitable only for private use and must be used in intermittent duty not more than 20 hours per 
month. It is recommended to use on-loading not more than a nominal, for 10-15 minutes and then to have a break 
for 20-30 minutes. This usage mode enables to complete domestic tasks effectively and prevents the tool from a 
premature coming out of order.
This manual contains the information and the requirements necessary and sufficient for a sure, effective and secure 
use of the rotary hammer.
Due to constant improving of the tool the manufacture reserves the right to make minor changes in its construction, 
not mentioned in this manual and not worsening its consumer and operational properties, effective and secure use. 

COMPLETENESS OF SET

The set contains:
1.  Electrical Rotary Hammer    1 pc.
2.  Side handle 

1 pc.

3.  Depth gauge 

1 pc.

4.  Dust collector 

1 pc.

5.  Set of spare carbon brushes  1 pc.
6.   Instruction manual 

1 pc.

7.  Warranty card 

1 pc.

8.  Packing box 

1 pc.

SPECIFICATIONS

Parameter    

Value

Maximum drilling diameter in concrete, mm

12

Maximum drilling diameter in wood, mm

20

Maximum drilling diameter in steel, mm

13

Impact energy, J

1,2

The number of operational modes

2

Safety clutch

No

Type of chuck

SDS-plus

Speed adjustment 

 Yes

Reverse

Yes

No load speed, min¯¹

0-1500

Impact rate, min¯¹

0-6600

Power, W

400

Rated voltage, V

230

Frequency, Hz

50

Cable length, m 

3

Power indicator 

No

Indicator of carbon brushes runout 

No

Protection class

IP20

Noise level, dB

72

Vibration level (ah), м/с

2

3,5

Degree of protection against electric shock

II

Weight net, kg

1.8

Weight gross, kg

2.0

Summary of Contents for 26601





























Reviews: