Remote Control Battery Installation
Power Source
4.If you cause a static discharge when touching the unit, and the unit fails
to function, simply unplug the unit from the AC outlet, wait a few minutes, and
plug it back in. The unit should return to normal operation.
Requires two AAA batteries(supplied).
Procedure
1. Turn the remote control face down. Remove battery
cover by pressing down on the marking on the
cover and sliding it off in the direction indicated.
2. Install batteries ma) and(-) polarity signs.
3. Replace the battery cover by sliding in reverse until
the lock snaps.
Note: Incorrect installation can cause battery leakage
and corrosion that will damage the Remote
control.
Precautions
Replace batteries in pair.
Do not mix battery types(zinc carbon with
alkaline).
Do not recharge, heat, short-circuit,
disassemble, or burn batteries.
Installation
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert the
AC cord plug into a standard 110V-240V 50/60HZ polarized AC outlet.
NOTE:
1.This TV can be connected to the specified voltage
(AC 110~240 volts / 50-60HZ).
2.If the polarized AC cord does not fit into a non-
polarized AC outlet, do not attempt to file or cut the
blade. It is the users responsibility to have an
electrician replace the obsolete outlet.
'
Combination VHF/UHF
Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm
twin-lead wire)
Connect the 75 ohm cable from a combination VHF/UHF antenna to
the antenna jack.
Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm
twin-lead)
Connect the UHF twin-lead wire to a combiner (not supplied).Connect
the VHF twin-lead to the 300-75 ohm matching transformer
(not supplied). Attach the transformer to the combiner. Attach
the combiner to the antenna jack.
Separate VHF/UHF Antenna
Connect the 75 ohm cable from the VHF antenna and the UHF antenna
twin-lead to a combiner (not supplied). Attach the combiner
to the antenna jack.
NOTE:
If your VHF antenna has a twin-lead wire, use the 300-75 ohm
matching transformer( not supplied), then connect the
transformer to the combiner.
For Subscribers to Basic
Cable TV Service
For basic cable service not
requiring a converter/
descrambler box,
connect the CATV 75 ohm
coaxial cable directly to the
antenna jack on the back of
the television.
For Subscribers to Scrambled Cable TV service
If you subscribe to a cable service which requires the use of a
converter/descrambler box, connect the incoming cable to the
converter/descrambler box and connect the output of the box to the
antenna jack on the back of the television. Follow the connections shown
left. Set the television to the output of the converter/descrambler box
(usually channel 3 or 4) and use the converter / descrambler box to select
channels.
For Subscribers to Unscrambled Basic Cable with
Scrambled Premium Channels
If you subscribe to a cable service in which basic cable channels are
unscrambled and premium channels require the use of a
converter/descrambler box, you may wish to use a two-set signal splitter
( sometimes called a two-set coupler )and an A/B switch box from the
cable installer or an electronics supply store. Follow the connections
shown left. With the switch in the B position, you can directly tune
any nonscrambled channels on your TV. With the switch in the A
position, tune your TV to the output of the converter/descrambler
box (usually channel 3 or 4) and use the box to tune scrambled channels.
Combination VHF/UHF Antenna
Single 75 ohm cable
300 ohm twin-lead wire
Splitter
Take off the Splitter
300-75 OHM MATCHING
TRANSFORMER
(not supplied)
UHF Antenna
300 ohm twin-lead wire
VHF Antenna
Single 75 ohm cable
300 ohm twin-lead wire
300-75 OHM MATCHING
TRANSFORMER
(not supplied)
COMBINER
(not supplied)
Incoming CATV
Converter/Descrambler
Converter/Descrambler
Splitter
A/B Switch A B
This television has an extended tuning range and can tune most
cable channels without using a cable company
¡°
supplied
converter
¡±
box. Some cable companies offer premium pay
channels in which the signal is scrambled. Descrambling these
signals for normal viewing requires the use of a descrambler
device which is generally provided by the cable company.
4
