ENG-3
ENG-4
FM radio
1. To select FM, press the
MODE
button, the display will show FM and the frequency.
2. To activate auto search, press
SELECT
button or press and hold
▼
/
▲
buttons until the radio
starts to scan the frequency band, the display will show ‘Scanning …‘(F6), and it will stop
automatically once a station has been found.
3. To search manually, press
▼
/
▲
buttons in the desired direction to increment the frequency by
0.05MHz. If reception is still poor adjust the position of the antenna or try moving the radio to
another location.
Scan setting
In
FM
mode, press and hold
MENU/INFO
button and then press
▼
/
▲
buttons to select
“Scan setting”. And press the
SELECT
button to confirm. Press
▼
/
▲
buttons to select
“All stations/Strong stations only”, and then press the
SELECT
button to confirm the setting.
USING HEADPHONES (not included)
A stereo headphone jack has been provided so that the radio can be used without disturbing others.
Plug in the headphones at the point marked ‘ ’ and adjust the listening volume to your chosen
level. Excessive sound pressure from earphones and headphones can cause hearing loss. The
speakers will not operate when earphones are fitted.
TECHNICAL SPECIFICATION
Rated voltage (adaptor)
Adaptor output
Rated voltage (radio)
Power consumption
Audio output
Radio
Operating conditions Temperature:
Unit dimension :
Weight :
***SPECIFICATION SUBJECT TO CHANGE WITHOUT FURTHER NOTICE.***
RESET
1. If moving the radio to another location in the country the pre-tuned and stored DAB stations
may no longer be available and it will be necessary to reset the radio back to the factory settings.
2. With the unit switched on, press and hold the
MENU/INFO
button and press
▼
/
▲
buttons
until the display shows ‘System’ and press the
SELECT
button and continue press
▼
/
▲
buttons
until the display shows “Factory Reset <No> Yes’ and press
▼
/
▲
buttons to “<Yes>” and press
the
SELECT
button. (F.7), (F.8)
3. The radio will display “Restarting….” and will then go into standby mode.
Note 1:
All stored programmed stations will be lost during reset.
Note 2:
Use the battery status without reset function.
DAB Auto Scan
The auto scan will search for the entire DAB Band III channels, After the scan has finished, the first
alphanumerically found stations will be automatically selected.
1. To activate auto scan, press and hold
MENU
button, and press
▼
/
▲
buttons to enter into the
Menu to select “Full scan”, finally press the
SELECT
button to confirm. The display will show
“Scanning…” and a pressing slide bar.(F.3)
2. All the stations that have been found will be stored automatically, press
▼
/
▲
buttons to
explore the stations that have been found. When you find a station that you would like to listen,
press the
SELECT
button to confirm.
DAB Manual tune
1. To select manual tune, press and hold
MENU/INFO
button, and then press
▼
/
▲
buttons to
select “Manual tune”(F.4). And press the
SELECT
button to confirm.
2. Press
▼
/
▲
buttons to move through the DAB channels, the display will show “5A to 13F” and
their associated frequencies. (F.5)
3. When your desired frequency appears in the display, press the
SELECT
button to listen, the
name of the station group (ensemble/multiplex) will be displayed.
Manual tune
< 5A 174.928MHz >
F.5
DAB
< Manual tune >
F.4
DAB
< Full scan >
F.3
92.75MHz
Scanning . . .
F.6
System
< Factory Reset >
Factory Reset ?
< No > Yes
F.7
F.8
AC 100 – 240V~ 50/60Hz, 0.2A
DC 6V 1A
DC 6V (1.5V x 4 AA)
6 W
2 W RMS
DAB 174-240MHz
FM 87.5-108MHz
5°C to 35°C
Humidity 5% to 90%
190 (L) × 110(W) × 115 (H) mm
0.8kg
DENVER DAB-35
DENVER DAB-35
