background image

II

FCC INFORMATION (For US customers)

1. PRODUCT

 

This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this 
product may not cause harmful interference, and (2) this product must accept any interference received, including 
interference that may cause undesired operation.

2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT

  This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. 

Modifi cation not expressly approved by DENON may void your authority, granted by the FCC, to use the product.

3. NOTE

  This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation.

  This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance 

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee 
that interference will not occur in a particular installation. If this product does cause harmful interference to radio or 
television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to 
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the product into an outlet on a circuit different from that to which the receiver is connected.
• Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for 

help.

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

n

 Cautions On Installation / Précautions d’installation / 

  Emplazamiento de la Instalación

z

z

z

 

z

Wall
Paroi
Pared

 

z

For proper heat dispersal, do not install this unit in a confi ned space, such as a bookcase or similar enclosure.

• More than 0.3 m (12 in.) is recommended.
• Do not place any other equipment on this unit.

 

z

Pour permettre la dissipation de chaleur requise, n’installez pas cette unité dans un espace confi né tel qu’une 
bibliothèque ou un endroit similaire.

• Une distance de plus de 0,3 m (12 po) est recommandée.
• Ne placez aucun matériel sur cet appareil.

 

z

Para la dispersión del calor adecuadamente, no instale este equipo en un lugar confi nado tal como una librería 
o unidad similar.

• Se recomienda dejar más de 0,3 m (12 pulg.) alrededor.
• No coloque ningún otro equipo sobre la unidad.

ESPAÑOL

ENGLISH FRANCAIS

n

 NOTES ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / 

NOTAS SOBRE EL USO

WARNINGS

AVERTISSEMENTS

ADVERTENCIAS

• Avoid high temperatures.

Allow for suffi cient heat dispersion 
when installed in a rack.

• Handle the power cord carefully.

Hold the plug when unplugging the 
cord.

• Keep the unit free from moisture, 

water, and dust.

• Unplug the power cord when not 

using the unit for long periods of 
time.

• Do not obstruct the ventilation 

holes.

• Do not let foreign objects into the 

unit.

• Do not let insecticides, benzene, 

and thinner come in contact with 
the unit.

• Never disassemble or modify the 

unit in any way.

• Ventilation should not be impeded 

by covering the ventilation 
openings with items, such as 
newspapers, tablecloths or 
curtains.

• Naked fl ame sources such as 

lighted candles should not be 
placed on the unit.

• Observe and follow local 

regulations regarding battery 
disposal.

• Do not expose the unit to dripping 

or splashing fl uids.

• Do not place objects fi lled  with 

liquids, such as vases, on the unit.

• Do not handle the mains cord with 

wet hands.

• When the switch is in the OFF 

position, the equipment is not 
completely switched off from 
MAINS.

• The equipment shall be installed 

near the power supply so that the 
power supply is easily accessible.

• Eviter des températures élevées.

Tenir compte d’une dispersion 
de chaleur suffi sante lors de 
l’installation sur une étagère.

• Manipuler le cordon d’alimentation 

avec précaution.
Tenir la prise lors du 
débranchement du cordon.

• Protéger l’appareil contre 

l’humidité, l’eau et la poussière.

• Débrancher le cordon 

d’alimentation lorsque l’appareil 
n’est pas utilisé pendant de 
longues périodes.

• Ne pas obstruer les trous 

d’aération.

• Ne pas laisser des objets étrangers 

dans l’appareil.

• Ne pas mettre en contact des 

insecticides, du benzène et un 
diluant avec l’appareil.

• Ne jamais démonter ou modifi er 

l’appareil d’une manière ou d’une 
autre.

• Ne pas recouvrir les orifi ces  de 

ventilation avec des objets tels que 
des journaux, nappes ou rideaux. 
Cela entraverait la ventilation.

• Ne jamais placer de fl amme  nue 

sur l’appareil, notamment des 
bougies allumées.

• 

Veillez à respecter les lois en 
vigueur lorsque vous jetez les piles 
usagées.

• L’appareil ne doit pas être exposé 

à l’eau ou à l’humidité.

• Ne pas poser d’objet contenant du 

liquide, par exemple un vase, sur 
l’appareil.

• Ne pas manipuler le cordon 

d’alimentation avec les mains 
mouillées.

• Lorsque l’interrupteur est sur la 

position OFF, l’appareil n’est pas 
complètement déconnecté du 
SECTEUR (MAINS).

• L’appareil sera installé près de la 

source d’alimentation, de sorte 
que cette dernière soit facilement 
accessible.

• Evite altas temperaturas.

Permite la sufi ciente  dispersión 
del calor cuando está instalado en 
la consola.

• Maneje el cordón de energía con 

cuidado.
Sostenga el enchufe cuando 
desconecte el cordón de energía.

• Mantenga el equipo libre de 

humedad, agua y polvo.

• Desconecte el cordón de energía 

cuando no utilice el equipo por 
mucho tiempo.

• No obstruya los orifi cios de 

ventilación.

• No deje objetos extraños dentro 

del equipo.

• No permita el contacto de 

insecticidas, gasolina y diluyentes 
con el equipo.

• Nunca desarme o modifi que  el 

equipo de ninguna manera.

• 

La ventilación no debe quedar 
obstruida por haberse cubierto 
las aperturas con objetos como 
periódicos, manteles o cortinas.

• No deberán colocarse sobre 

el aparato fuentes infl amables 
sin protección, como velas 
encendidas.

• A la hora de deshacerse de las 

pilas, respete la normativa para el 
cuidado del medio ambiente.

• No exponer el aparato al goteo o 

salpicaduras cuando se utilice.

• No colocar sobre el aparato objetos 

llenos de líquido, como jarros.

•  No maneje el cable de alimentación 

con las manos mojadas.

• Cuando el interruptor está en la 

posición OFF, el equipo no está 
completamente desconectado de 
la alimentación MAINS.

• El equipo se instalará cerca de la 

fuente de alimentación de manera 
que resulte fácil acceder a ella.

1.RCDM38E3̲ENG̲004̲1st.indd   F4

1.RCDM38E3̲ENG̲004̲1st.indd   F4

2010/05/17   14:17:03

2010/05/17   14:17:03

Summary of Contents for D-M38






































Reviews: