103
Audio
Audio Delay
Default settings are underlined.
While viewing video, manually adjust the time to delay audio output.
Setting details
0ms – 200ms
• This item can be set within the range of 0 to 100 ms when “Auto Lip Sync” (
“On” and when a TV compatible with Auto Lip Sync is connected.
• Store “Audio Delay” for each input source.
• Audio Delay for game mode can be set when “Video Mode” (
) is set to “Auto” or
“Game”.
Volume
Default settings are underlined.
Set the MAIN ZONE (room where the unit is located) volume setting.
Setting items
Setting details
Scale
Set how volume is
displayed.
0 – 98
: Display in the range 0 (Min) to 98.
–79.5dB – 18.0dB
: Display ---dB (Min), in the range –79.5 dB to 18.0 dB.
• The “Scale” setting is applied also to the “Limit” and “Power On Level”
display method.
• The “Scale” setting applies to all zones.
Limit
Make a setting for
maximum volume.
Off
: Do not set a maximum volume.
60 (–20dB)
/
70 (–10dB)
/
80 (0dB)
Power On Level
Define the volume setting
that is active when the
power is turned on.
Last
: Use the memorized setting from the last session.
Mute
: Always use the muting on condition when power is turned on.
1 – 98 (–79dB – 18dB)
: The volume is adjusted to the set level.
Mute Level
Set the amount of
attenuation when muting
is on.
Full
: The sound is muted entirely.
–40dB
: The sound is attenuated by 40 dB down.
–20dB
: The sound is attenuated by 20 dB down.
Audyssey
Default settings are underlined.
Set Audyssey MultEQ® XT, Audyssey Dynamic EQ® and Audyssey Dynamic Volume®. These can be
selected after Audyssey® Setup has been performed. For additional information on Audyssey technology,
please see
.
NOTE
• If you have not performed Audyssey® Setup, or if you change the speaker settings after performing
Audyssey® Setup, you may not be able to select Dynamic EQ/Dynamic Volume.
In this case, either perform Audyssey® Setup over again or perform “Restore...” (
) to
return to the settings after Audyssey® Setup was run.
• When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the “Audyssey”
cannot be set.
Setting items
Setting details
MultEQ®XT
MultEQ® XT compensates
for both time and
frequency characteristics
of the listening area based
on Audyssey® Setup
measurement results.
Selection is done from three
types of compensation
curves. We recommend the
“Audyssey” setting.
MultEQ® XT is the
prerequisite function for
Dynamic EQ and Dynamic
Volume.
Audyssey
: Optimize the frequency response of all speakers.
Audyssey Byp.L/R
: Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat
: Optimize frequency response of all speakers to flat
response.
Graphic EQ
: Apply frequency response set with “Graphic EQ”
Off
: Turn “MultEQ® XT” equalizer off.
• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be
selected after Audyssey® Setup has been performed. “Audyssey”
is automatically selected after performing Audyssey® Setup. When
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,
illuminates.
• After running Audyssey® Setup, if the Speaker Configuration, Distance,
Channel Level, and Crossover Frequency have changed without
increasing the number of speakers measured, only
illuminates.
NOTE
When using headphones, “MultEQ® XT” is automatically set to “Off”.
“MultEQ® XT”, “Dynamic EQ” and “Dynamic Volume” settings are stored for each input source.
Basic v
ersion
A
dv
anced v
ersion
Inf
or
mations
A
dv
anced v
ersion
v
See overleaf
DVD
