Demco Excalibar 3 Operator'S Manual Download Page 5

TB20061

Page 5

During Operation

 

Always follow state and local regulations regarding auxiliary lighting when towing. Be sure to check with local law enforcement 

agencies for your own particular regulations. Only safety cables (not elastic or nylon/plastic tow straps) should be used to retain 

connection between towing unit and towed vehicle in event of separation.

•  Do not load towed vehicle with cargo. Towed vehicles exceeding weight limits will overload tow bar and may cause serious injury 

and damage.

•  Beware of bystanders, 

PARTICULARLY CHILDREN! 

Always look around to make sure it is safe to start engine of towing unit and mov-

ing towed vehicle. This is particularly important with higher noise levels, as you may not hear people shouting. 

  NO PASSENGERS ALLOWED

- Do not carry passengers anywhere on or in towed vehicle.

•  When halting operation, even periodically, set towing unit’s parking brake, shut off engine, and

 remove ignition key

.

•  Be extra careful on inclines.

• 

MANEUVER TOWING UNIT AT SAFE SPEEDS.

•  Avoid overhead wires or other obstacles. Contact with overhead lines could cause serious injury or death.

•  Avoid loose gravel, rocks, and holes; they can be dangerous for unit operation or movement.

•  Allow for unit length when making turns.

•  Do not work under raised components or attachments unless securely positioned and blocked.

•  Keep all bystanders and pets clear of work area.

•  Operate towing unit from operators seat only.

•  As a precaution, recheck  hardware on tow bar  every 200 miles, and correct all problems. Follow maintenance safety proce-

dures.

Following Operation

•  Following operation, or when unhooking, stop towing vehicle, set parking brake, shut off engine and 

remove ignition key

.

•  Store tow bar  in area away from human activity.

•  Do not permit children to play on or around stored tow bar.

•  Make sure parked vehicle is on hard, level surface.

•  Wheel chocks may be needed to prevent vehicle from rolling.

Highway and Transport Operations

•  Adopt safe driving practices:

  -    Always drive at safe speed relative to local conditions and ensure that your speed is low enough for an 

  emergency 

stop.

  -   Reduce speed prior to turns to avoid risk of overturning.

  -   Always keep towing unit in gear to provide engine braking when going downhill. Do not coast.

  -   Do not drink and drive!

•  Comply with state and local laws governing highway safety.

•  Local laws should be checked for all highway lighting and marking requirements.

•  Plan your route to avoid heavy traffic.

•  Be a safe and courteous driver.  Always yield to oncoming traffic in all situations, including narrow bridges, intersections, etc.

•  Watch for obstructions overhead and to both sides while towing vehicle.

•  Operate with maximum visibility at all times.  Make allowances for increased length and weight when making turns and stop-

ping.

Safety Information

Summary of Contents for Excalibar 3





















Reviews: