Delta N-12K User Manual Download Page 17 | Manualshive

Page: 17 / 27

background image

After diagnostic test, the load is supplied by the inverter; if the diagnostic test fails, the
error messages will be shown as below.

ERROR MESSAGES

CHARGER FAILURE
SHUT DOWN

BAD BATTERY
SHUT DOWN

DC BUS FAILURE
SHUT DOWN

INVERTER FAILURE
SHUT DOWN

OUTPUT FAILURE
SHUT DOWN

FAN FAILURE
SHUT DOWN

CHARGER FAILURE

INVERTER FAILURE

OUTPUT FAILURE

FAN FAILURE

BAD BATTERY

DC BUS FAILURE

Power Off Inverter

Press the ”OFF” button on front control panel to disable the inverter:



If the AC input power exists, the UPS will be switched to BYPASS mode.



If the UPS is in backup mode, the message ”UPS OFF WAITING” will be displayed on LCD

about thirty seconds then disappear.



Before removing the battery connect wire, please wait until the message “UPS OFF

WAITING” displayed on LCD disappears.

14

«
...
15
16
17
18
19
...
»

Summary of Contents for N-12K




























Reviews:

No comments

Related manuals for N-12K

OnePower Line Interactive UPS A03-S1001

Brand: Atlantis Land Pages: 50

Brand: Salicru Pages: 34

Brand: Lenovo Pages: 76

Brand: Lenovo Pages: 102

Brand: Lenovo Pages: 13

Brand: Toshiba Pages: 138

Brand: OPTI-UPS Pages: 34

Brand: Eaton Pages: 206

Brand: SEI Pages: 14

SmartPro SMX1200XLHG

Brand: Tripp Lite Pages: 5

SmartPro SMART3000RMXL2U

Brand: Tripp Lite Pages: 6

SmartPro Rackmount SMX3000XLRT2U

Brand: Tripp Lite Pages: 6

SmartPro Rackmount SMX1000RT2U

Brand: Tripp Lite Pages: 6

SmartPro SMX2200XLRT2U

Brand: Tripp Lite Pages: 60

Brand: Xtreme Power Conversion Pages: 48

Brand: Xtreme Power Conversion Pages: 85

Brand: CertaUPS Pages: 22

Brand: V7 Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands