Delta LYTE DRL-24V480W1A Series Technical Data Sheet Download Page 2

TECHINCAL DATASHEET

 

LYTE DIN Rail Power Supply 

24V 480W 1 Phase / DRL-24V480W1A

□ 

 

 

  

All parameters are specified at 25°C ambient and AC input unless otherwise indicated.

 

  www.DeltaPSU.com (December 2020, Rev. 05) 

 

2

 

Specifications 

Input Ratings / Characteristics 

 

Nominal Input Voltage 

100-240Vac 

Input Voltage Range 

85-264Vac  

Nominal Input Frequency 

50-60Hz 

Input Frequency  Range 

47-63Hz 

DC Input Voltage Range* 

120-375Vdc 

Input Current 

5.4A typ. @ 115Vac, 2.7A typ. @ 230Vac 

Efficiency at 100% Load 

85% typ. @ 115Vac, 88% typ. @ 230Vac 

Max Power Dissipation 

0% load 

 
 

5W @ 115Vac 

4W @ 230Vac 

  

 

100% load  50W @ 115Vac 

40W @ 230Vac 

Max Inrush Current (Cold Start) 

40A typ. @ 115Vac,  80A typ. @ 230Vac 

Power Factor at 100% Load 

> 0.95 @ 115Vac & 230Vac 

Leakage Current 

< 1mA @ 264Vac 

*Fulfills test conditions for DC input. Safety approval for DC input can be obtained upon request.

 

 

 

Output Ratings / Characteristics** 

 

Nominal Output Voltage 

 

24Vdc 

Factory Set Point Tolerance 

 

24Vdc ± 2% 

Output Voltage Adjustment Range 

 

22-28Vdc 

Output Current 

 

20.0A (480W max.) 

Output Power 

 

480W 

Line Regulation 

 

< 0.5% (@ 85-264Vac, 100% load) 

Load Regulation 

 

< 1.5% (0-100% load) @ > -10°C to +70°C 

< 2.0% ( 0-100% load) @ 

≤ 

-10°C to -20°C 

PARD*** (20MHz) 

 

< 120mVpp @ 0°C to +70°C 

< 240mVpp @ < 0°C to -10°C 

< 360mVpp @ < -10°C to -20°C 

Rise Time 

 

100ms typ. @ nominal input (100% load) 

Start-up Time 

 

1,000ms typ. @ 115Vac & 230Vac (100% load

)

 

Hold-up Time 

 

10ms typ. @ 115Vac (100% load

)

 

16ms typ. @ 230Vac (100% load

)

 

Dynamic Response  

(Overshoot & Undershoot O/P Voltage) 

 

± 10% (2400mVpp) @ 85-264Vac input, 0-50% load, 50-100% 

load 

(Slew Rate: 0.1A/μ

s) 

Start-up with Capacitive Loads 

 

8,000µF Max 

Functional 

DC OK Relay Contact  30V / 1A 

The relay contact are normally “ON” (closed) when the output 

(Vout) is greater than 90% of its rated value. 

**For power de-rating from 40°C to 70°C @ 115Vac & 50°C to 70°C @ 230Vac, and Vin < 100Vac, see power de-rating on page 3. 

***PARD is measured with an AC coupling mode, 5cm wires, and in parallel with 0.1μF ceramic capacitor & 47μF electrolytic cap

acitor. 

 

 

 

Downloaded from

Arrow.com.

Downloaded from

Arrow.com.

Summary of Contents for LYTE DRL-24V480W1A Series
















Reviews: