background image

12

13

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

The fan is not turning on 1.  Power off

2.  Faulty switch
3.  Faulty wire connection

1.  Make sure power supply is on.
2.  Test or replace switch.
3.  Check wire in switch box.

The fan seems louder 

than it should

1.  CFM too great 

2.  Damper not working 

properly or damaged 

3.  Bend in duct too close 

to fan discharge

4.  Fan discharge reduced 

to fit smaller duct 

5.  Fan body not securely 

attached

1.  Be sure the CFM rating on the fan matches the 

size of your room.

2.  Check damper to ensure it is opening and 

closing properly. If the damper has become 

damaged, please call Customer Service.

3.  Be sure you do not have any sharp bends in 

duct closer than 18 in. to the fan discharge.

4.  Use recommended size ducting to reduce fan 

noise.

5.  Be sure the fan is securely attached to your 

ceiling joists.

The fan is not clearing 

the room

1.  Insufficient intake 

airfow within room 

 

2.  Insufficient CFM

1.  Be sure a door or window is slightly ajar or 

opened to allow airflow. The fan is not able to 

draw air out of the room without enough airflow 

to draw in from.

2.  Be sure the CFM rating on the fan matches the 

requirements for your room size.

The fan keeps running
even though the house
humidity level is lower
than set humidity level

1.  Our sensor tolerance 

is +/-10% RH 

2.  Outdoor humidity is 

back drafting to the fan

1.  Continue to let the fan run since it is good to 

keep venting the house and the electric bill is 

minimal (approximately less than $10 per year).

2.  Turn the fan off when not in use.

TROUBLESHOOTING

DIMENSIONS

12

12

3/4

8

1

9

Ø4

3/8

3/8

5/8

1/2

Unit: Inch

Summary of Contents for Breez 110F















Reviews: