background image

ATTACHING FOLLOWER ARM TO 
CARRIAGE ASSEMBLY

Insert follower arm (A) Fig. 22 into hole in arm (B) of carriage assembly and
tighten thumb screw (C). 

NOTE:

Pin (D) of follower arm (A) should point

toward right end of duplicator rail.

6

ATTACHING DUPLICATOR TO 
WOOD LATHE

For Model 46-860, 46-715, and 46-745 Wood Lathes Only.

1.

Slide two T-bolts (G) Fig. 23 into channel located at the rear of duplica-

tor guide rail (H).

2.

Place mounting pad (J) Fig. 24 between two T-bolts (G) and slide T-bolts

inward into slots of mounting pad (J) and fasten with two M10 flat washers
(K) and M10 hex nuts (L). 

NOTE:

Loosely tighten hardware.

NOTE: 

Use top hole of bracket (A) Fig. 24 for Model 46-715 14" lathe only.

Use the center hole (B) Fig. 24 for all 16" lathes.

3.

Attach the remaining mounting pad to the other end of duplicator pad in

the same manner.

4.

IMPORTANT: To prevent personal injury or damage to the duplica-

tor, use two or more people to mount the duplicator to the mounting
brackets.

5.

While carefully supporting the duplicator rail (H) Fig. 25 at both ends,

slide the mounting pad (J) along the duplicator rail until the tapped hole in
mounting pad (J) lines up with slot in mounting bracket (C). Fasten with M16
x 35mm hex socket head screw (M) and 

16mm x 41mm 

flat washer (N). 

NOTE:

For 46-715 or 46-745, use bracket (A) Fig. 27B with M8 x 55mm socket
head set screw without washer.

6.

Tighten two hex nuts (L) Fig. 26 and two hex socket head bolts (E) and

(M).

7.

Mount duplicator assembly (H) Fig. 27A to mounting bracket (C) at the

other end of the lathe in the same manner. 

Tighten all mounting hardware.

Replace tailstock on the machine. 

Fig. 22

Fig. 23

Fig. 24

Fig. 25

Fig. 26

Fig. 27A

Fig. 27B

C

B

A

D

A

B

G

K

L

G

H

C

J

H

N

B

L

L

M

E

C

H

A

J

G

Summary of Contents for 46-408





















Reviews: