![background image](http://html.mh-extra.com/html/delta-therm/pck-c6/pck-c6_installation-instructions_2478769002.webp)
Detail 3.
Score and remove 1.75” (5cm) of the jacket to
expose
the black core
.
Shave the black material from the bus wires along
the
edges of the core, then cut away the center
material
to free the bus wires.
en cut a
Cut the .125” x 2.5” (.3 x 6cm) piece of shrink
sleeve
in half. Slide the sleeves over each bus wire,
leaving .5"
(1cm) of bus wire exposed. Apply heat to
shrink the sleeves.Slide a .5” x 1.5” (1 x 4cm) shrink
sleeve over
the
two bus wires so that .75” (2cm)
covers the cable
body
and .75” (2cm) covers the bus
wires. Apply
heat to
shrink the sleeve. While the
sleeve is still
hot, use
needle-nose pliers to squeeze
the sleeve
between the
bus wires. To ensure a
watertight seal,
hold the pliers
in place until the sleeve
cools.
Using a pipe strap (not supplied), fasten the
standoff
bracket to the pipe.
Insert the connector body through the bracket,
then
attach the junction box (not supplied) to the
connector
body
.
Push the cable through the connector body,
moving
the
grommet, the gland washer, and the
connector
cap to
the connector body. Then tighten
the
cap to the
body.
Attach the non-insulated ring connector to the cold
lead,
then use the grounding screw to attach the
ring
connec-tor to the standoff bracket.
Using the closed-end crimp connectors, connect
the
bus
wires to 14 AWG power feed wires
.
Push the connection into the junction box, then
attach
the gasket and cover.
7.
8
.
9
.
10
.
15
.
14
.
11
.
12
.
13
.
PCK-TT
and PCK-C6
Installation Instructions continued...
Cable with braid
1.
Slide the braid back from the end of the cable and
squarely remove 1.5” (4cm) from the end of the cable,
ensuring that the conductors do not touch each other.
2.
Slide a
0.
5” x 1.5” (.64 x 4cm) shrink sleeve over the
end of the cable, covering only 1” (3cm) of the cable.
3.
Apply heat to shrink the sleeve. While the sleeve is still
hot, use needle-nose pliers to squeeze the end of the
sleeve. To ensure a watertight seal, hold the pliers in
place until the sleeve cools.
4.
Slide the braid over the shrink sleeve, then twist the
end of the braid into a cold lead.
Cable with braid and Overjacket
(CO)
1.
Score and remove 3” (8cm) of the overjacket from the
end of the heater.
2.
Slide the braid back from the end of the cable and
squarely remove 1.5” (4cm) from the end of the cable,
ensuring that the conductors do not touch each other.
3.
Slide a .25” x 1.5” (.64 x 4cm) shrink sleeve over the
end of the cable, covering only 1” (3cm) of the cable.
4.
Apply heat to shrink the sleeve. While the sleeve is
still
hot, use needle-nose pliers to squeeze the end of
the
sleeve. To ensure a watertight seal, hold the pliers
in
place until the sleeve cools.
5.
Slide the braid over the shrink sleeve, then twist the
end of the braid into a cold lead.
6.
Slide the
0.5
” x 6” (1 x 15cm) shrink sleeve over the
braid, leaving .5” (1cm) extending beyond the end of
the
cold lead.
7.
Apply heat to shrink the sleeve. While the sleeve is
still
hot, use needle-nose pliers to squeeze the end of
the
sleeve. To ensure a watertight seal, hold the pliers
in
place until the sleeve cools.
aTTaChINg ThE CablE TO PIPE
1.
Using fiberglass tape, attach the cable to the
pipe
at one-foot intervals.
2.
A
fter the pipe has been insulated, a
ttach a
caution label in a visible location near the
standoff bracket and at frequent intervals along
the
heat-traced pipe.
TEChNICal SuPPORT
Please call Delta-Therm Corporation at 1-800-526-7887
with any installation or operating questions.
WARNING
WARNING: This kit and the cable used with it must
be installed by a qualified electrician. All assembly,
installation, and test instructions must be followed.
Improper installation can result in property damage,
serious injury, and/or death due to electric shock and
fires. Please call Delta-Therm Corporation at 1-800-
526-7887 with any installation or operating questions.
(847) 526-2407 Fax (847) 526-4456
(800) 526-7887
DELTA-THERM
Corporation,
6711 Sands Road Suite A, Crystal Lake, IL 60014
CA_SR_PCK
_C6
_1
9
10
_II