background image

 

 

 

Copyright Information 

© 2003 Delta Tau Data Systems, Inc. All rights reserved. 

This document is furnished for the customers of Delta Tau Data Systems, Inc. Other uses are 
unauthorized without written permission of Delta Tau Data Systems, Inc.  Information contained 
in this manual may be updated from time-to-time due to product improvements, etc., and may not 
conform in every respect to former issues. 

To report errors or inconsistencies, call or email:  

Delta Tau Data Systems, Inc. Technical Support 

Phone: (818) 717-5656 
Fax: (818) 998-7807 
Email: 

[email protected]

 

Website: 

http://www.deltatau.com

 

Operating Conditions 

All Delta Tau Data Systems, Inc. motion controller products, accessories, and amplifiers contain 
static sensitive components that can be damaged by incorrect handling.  When installing or 
handling Delta Tau Data Systems, Inc. products, avoid contact with highly insulated materials.  
Only qualified personnel should be allowed to handle this equipment. 

In the case of industrial applications, we expect our products to be protected from hazardous or 
conductive materials and/or environments that could cause harm to the controller by damaging 
components or causing electrical shorts.  When our products are used in an industrial 
environment, install them into an industrial electrical cabinet or industrial PC to protect them 
from excessive or corrosive moisture, abnormal ambient temperatures, and conductive materials.  
If Delta Tau Data Systems, Inc. products are exposed to hazardous or conductive materials and/or 
environments, we cannot guarantee their operation.

 

 

 

 

Summary of Contents for TURBO 4AX-603625-XUXX






























Reviews: