Delta OHM HD45 17A Manual Download | Manualshive

Page: 16 / 72

background image

- 16 -

In simplified mode, if the instrument is supplied with display and keyboard, thresholds
can easily be viewed and changed by pressing the MENU key (for least than 2
seconds).

The threshold values of the quantities measured by the instrument are shown on the
display. The

S

symbol on top left of the display indicates that you are in the threshold

values screen. A full flashing cursor appears next to one of the available thresholds.
Thresholds can be changed as follows:

1.

If necessary, move the cursor on the desired threshold with “

▼

” and “

▲

” keys.

2.

Press MENU, the cursor passes in “underlined” mode.

3.

Change the value with “

▼

” and “

▲

”keys.

4.

Confirm by pressing MENU (or press ESC if you don’t want to save the

changes).

«
...
14
15
16
17
18
...
»

Summary of Contents for HD45 17A









































































Reviews:

No comments

Related manuals for HD45 17A

Brand: MAGNELAB Pages: 2

Brand: Arteche Pages: 9

Brand: jablotron Pages: 3

THERMASGARD ALTM 2-VA

Brand: S+S Regeltechnik Pages: 16

Brand: Yaesu Pages: 165

Brand: AAS Pages: 4

IMI Sensors 682C33

Brand: PCB Piezotronics Pages: 22

Brand: S+S Regeltechnik Pages: 16

40103/202/3/5/10

Brand: RCD Pages: 2

Brand: MKS Pages: 55

FX-300 TWIN PMR 446

Brand: BRONDI Pages: 20

Brand: COP Pages: 5

Brand: JVC Pages: 2

Kenwood TK-5220

Brand: JVC Pages: 128

Brand: Mercoid Pages: 20

Brand: Wulfsberg Pages: 40

Brand: Baumer Pages: 3

Brand: Baumer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands