Delta Controls DSC-1616 Installation Manual Download Page 12

Delta Controls 

Page 12 of 12 

 
FCC Compliance Information 

 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 
15  of  the  FCC  Rules.  These  limits are designed  to  provide reasonable protection against  harmful  interference 
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate 
radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the  instruction  manual,  may  cause 
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause 
harmful interference in which case the user will be required to correct the interference at his own expense. 
 

Industry Canada Compliance Statement 
 

ICES-003   This  Class  A  digital  apparatus  meets  all  requirements  of  the  Canadian  Interference-Causing 

Equipment Regulations 

 
 

Cet appareil numérique de la Classe A Respecte toutes les exigences du Règlement sur le matérial 
brouiller du Canada. 

 
 

 

    

This product conforms to the following UL requirements:

 

UL916: Energy Management Equipment 

UL864*: Control Units and Accessories for Fire Alarm Systems, 9

th

 Edition 

 

* - Applicable to DSC-1616E-UL864 model only 

 

 

Summary of Contents for DSC-1616













Reviews: