20
Make sure there are no milk residues left
inside the holes and the groove on the fine
end of the froth regulator.
5. Check that the intake tube and spout are not
clogged with milk residues.
6. Replace the froth regulator, milk spout and
intake tube.
7. Replace the lid on the milk container, turning
it anticlockwise to hook it in place.
DESCALING
Descale the machine when the message
“DESCALE!” flashes on the display.
Important!
Descaler contains acids which may irritate the
skin and eyes.
It is vital to respect the manufacturer’s safety
warnings given on the descaler pack and the
warnings relating to the procedure to follow in
the event of contact with the skin and eyes.
Please note!
Under no circumstances should you use
sulphamic or acetic based descalers. Their use
invalidates the guarantee.
Failure to descale the appliance as described also
invalidates the guarantee.
1. Turn the machine on.
2. Enter the programming menu by pressing
the
P
icon.
3. Select by pressing the
OK
icon.
“Descaling Confirm?” is displayed. Press
OK
to enable the function.
4. The message “Add descaler” “Press OK” is
displayed.
5. Before confirming, empty the water tank
(A13).
Pour the descaler diluted with water
(respecting the proportions indicated on the
descaler pack) into the water tank.
Place an empty container with a minimum
capacity of 1.5 litres under the hot water
spout.
Important! Danger of burns
Hot water containing acid flows out of the hot
water spout.
Avoid contact with splashes of water.
6. Confirm by pressing the
OK
icon.
7. The message “Descaling...” is displayed.
The descaling programme starts and the
descaler liquid comes out of the water spout.
The descale programme automatically
performs a series of rinses and pauses to
remove limescale deposits from inside the
machine.
After about 30 minutes, the message “Rinsing
FILL TANK!” is displayed.
8. The appliance is now ready for rinsing
through with clean water.
Remove the water tank, empty, rinse under
running water, fill with clean water and
replace. “Rinsing... Press OK” is displayed.
9. Empty the container used to collect the
descaler solution and replace it under the hot
water spout.
10. Press the
OK
icon to start rinsing. Hot water
flows out of the spout and the message
“Rinsing...” is displayed.
11. When the water tank is completely empty,
the message “Rinsing Complete... Press OK”
is displayed.
12. Press the
OK
icon. The appliance goes off.
To use it again, turn the appliance on by pressing
the
button.
SETTING WATER HARDNESS
The DESCALE message is displayed after a
period of time established according to water
hardness.
The machine is set by default for a hardness
value of 4 (very hard water).
The machine can also be programmed according
to the actual hardness of the mains water in
the various regions, varying the frequency with
which the message is displayed.
Measuring water hardness
1. Remove the “TOTAL HARDNESS TEST”
indicator paper from its pack.
2. Immerse the paper completely in a glass of
water for one second.
3. Remove the paper from the water and shake
lightly. After about a minute, 1, 2, 3, or 4 red
squares form, depending on the hardness of
the water. Each square corresponds to one
level.
Summary of Contents for PrimaDonna Avant ESAM 6700 EX2
