17
Customizing the “My LONG coffee” quantity
The appliance is set by default to automatically
deliver 3.38 fl.oz/100 ml of “My coffee”. To modify
these settings, proceed as follows:
1. Place a sufficiently large cup or glass under the coffee
spouts (fig. 9).
2. Press the
icon repeatedly (fig. 8)until “My coffee”
is displayed.
3. Press the
LONG
icon. The machine starts delivering coffee;
4. Press the
PROG
icon. The appliance starts programming;
5. As soon as the coffee in the cup reaches the required level,
press the
STOP
icon again.
The quantity set has now been programmed.
Please note!
• To cancel programming of “My LONG coffee”, press the
EXIT
PROG
icon.
“My LONG coffee” can be customised in all profiles (see
“Memorising your personal profile” on page 18).
DELIVERING HOT WATER AND STEAM
Important! Danger of burns.
Do not leave the appliance unattended while delivering hot
water or steam. The spout becomes hot during delivery. Hold
by the handle only.
Please note!
If Energy Saving is active, you may have to wait a few seconds
before hot water and steam are delivered.
Delivering hot water
1. Check that the hot water spout is attached correctly.
2. Place a container under the water spout (as close as possi-
ble to avoid splashes) (fig. 4).
3 Press the
icon (fig. 37).
4. Hot water delivery begins and then stops automatically. A
progress bar fills gradually as preparation proceeds. To in-
terrupt delivery of the hot water manually, press the
STOP
icon again.
Please note!
The quantity of hot water can be customised in all profiles
(see “Memorising your personal profile” on page 18).
Change the quantity of water delivered
automatically
The machine is set by default to automatically delivery 8.45
fl.oz/250 ml of hot water. To modify these quantities, proceed
as follows:
1. Check that the hot water spout is attached correctly.
2. Position a container under the spout.
3. Press the
icon, then the
PROG
icon.
4. When the hot water in the cup reaches the required level,
press the
STOP
icon.
The machine is now reprogrammed with the new quantity.
Please note!
• To cancel programming, press the
EXIT PROG
icon.
Steam delivery
1. Check that the hot water spout is attached correctly.
2. Fill a container with the liquid to be heated or frothed and
immerse the steam spout in the liquid.
3 Press the
icon (fig. 37). After a few seconds, the steam
to heat the liquid comes out of the cappuccino maker;
4. When the required temperature is obtained, interrupt
steam delivery by pressing the
STOP
icon. (You should not
discharge steam for more than 3 minutes at a time).
Important!
Always stop steam delivery before extracting the container con-
taining the liquid to avoid burns from splashes.
Tips for using steam to froth milk
• When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially skim-
med milk at refrigerator temperature (about 41°F/5°C).
• For a creamier froth, rotate the container with slow move-
ments in an upward direction.
• To avoid milk with poor froth or large bubbles, always clean
the spout as described in the following section.
Clean the steam/hot water spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
1. Place a container under the cappuccino maker and deliver
a little water by pressing the
icon (fig. 37). Stop
delivery of hot water by pressing the
STOP
icon again.
2. Wait a few minutes for the cappuccino maker to cool down,
then extract the hot water spout (fig. 38) by pressing the
button. Hold the spout with one hand and with the other,
turn the cappuccino maker and pull it downwards (fig. 39).
3. Also remove the steam nozzle by pulling it downwards (fig.
40).
4. Check the hole in the nozzle shown by the arrow in fig. 41
is not blocked. If necessary, clean using a toothpick.
5. Wash all parts of the spout thoroughly with a sponge and
warm water.
