10
The appliance is ready for use only after completion of this
cycle.
danger of burns!
during rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
avoid contact with splashes of water.
• To turn the appliance on, press the
button (fig. 5).
The message “heaTing uP, PleaSe WaiT” is displayed.
after heating, the message “rinSing” is displayed. as well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance is at temperature when the message “ready
STandard TaSTe” is displayed.
TURNING THE APPlIANCE OFF
each time the appliance is turned off, it performs an automatic
rinse cycle which cannot be interrupted.
important!
To avoid damaging the appliance, always press the
button to turn off.
danger of burns!
during rinsing, a little hot water flows from the coffee spouts.
avoid contact with splashes of water.
To turn the appliance off, press the
button (fig. 5).
Please note:
if the appliance is not used for an extended period, place the
main switch in the
0
position (fig. 6).
never place the main switch in the 0 position while the
appliance is on.
MENU SETTINGS
The following menu items can be selected: Clock, Start, auto-
start, descale, Temperature, off after, Water hardness, default
values.
To access the settings menu, press the
MENU
button. The light
on the button comes on.
Clock
To adjust the time on the display, proceed as follows:
1. access the menu and press the
NEXT
button until “CloCK”
is displayed;
2. Press the
CHANGE
button to change the time (hold the
button down to change the time rapidly). When you have
finished, release the button. The time flashes.
3. Press the
OK
button to confirm;
4. Press the
MENU
button to exit the menu. The light on the
button goes off.
The time displayed when the machine is off (stand-by) is now
set.
Turning on
once “auTo-STarT yes” has been enabled, the auto-start time
must be set as follows:
1. access the menu and press the
NEXT
button until “STarT”
is displayed.
2. Press the
CHANGE
button to change the start time (hold
the button down to change the time rapidly). When you
have finished, release the button. The auto-start time
flashes on the display.
3. Press the
OK
button to confirm.
4. To exit the menu, press the
MENU
button. The light on the
button goes out.
The auto-start time has been programmed.
Auto-start
you can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function,
the time must be set correctly
(see
previous section “Clock”).
To set the auto-start time, proceed as described in the section
below.
1. access the menu and press the
NEXT
button until “auTo-
STarT no” or “auTo-STarT yes” (if the function has been
enabled) is displayed;
2. Press the
CHANGE
button to change the selection. The
new selection flashes on the display;
3. Press the
OK
button to confirm;
To set the auto-start time, proceed as described in the section
below.
The
symbol is displayed alongside the clock to indicate
that auto-start has been programmed (in stand-by).
Descaling
For instructions on descaling, see page 15.
Temperature
To modify the temperature of the water used to make the
coffee, proceed as follows:
1. access the menu and press the
NEXT
button until
“TeMPeraTure” is displayed;
2. Press the
CHANGE
button until the required temperature
(low, medium, high, maximum) is displayed;
3. Press the
OK
button to confirm;
4. Press the
MENU
button to exit the menu. The light on the
button goes off.
