14
8.10 Customising the “LONG coffee” quantity
The appliance is set by default to automatically deliver about
180ml of LONG coffee. To modify these settings, proceed as
follows:
1. Place a sufficiently large cup or glass under the coffee
spouts (A7-fig. 12).
2. Press and hold the
button (B8-fig. 18) until “Pro-
gram quantity” is displayed.
3. Release the
button. The appliance starts delivering
coffee;
4. As soon as the coffee in the cup reaches the required level,
press the
button again.
The quantity of coffee in the cup has now been programmed.
Please note!
If the programme uses pre-ground coffee, the appliance will
prompt you to add a second level measure (C2) of coffee.
9. MAKING CAPPUCCINOS AND MILK BASED
COFFEES
Please note!
• To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid (D2) and hot water con-
nection nozzle (A8) as described in sections “9.5 Cleaning
the milk container after every use”, “11.10 Cleaning the
milk container” and “11.11 Cleaning the hot water connec-
tion nozzle”.
9.1 Filling and attaching the milk container
1. Remove the lid (D2) (fig. 19);
2. Fill the milk container (D3) with a sufficient quantity of
milk, not exceeding the MAX level marked on the handle
(fig. 20). Each mark on the side of the container corre-
sponds to about 33,38 fl.oz/100 ml of milk;
Please note!
• For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
41°F/5°C).
• If “Energy saving” mode is enabled, you may have to wait a
few seconds before the drink is delivered.
3. Make sure the milk intake tube (D4) is correctly inserted in
the bottom of the milk container lid (fig. 21);
4. Place the lid back on the milk container;
5. Remove the hot water spout (C6) (fig. 22);
6. Attach the milk container (D) to the connection nozzle (A8-
fig. 23) and push as far as it will go. The machine emits a
beep (if the beep function is enabled);
7. Place a sufficiently large cup under the coffee spouts (A7)
and frothed milk spout (D5). Adjust the length of the milk
spout. To move it nearer the cup, simply pull it downwards
(fig. 24).
8. Follow the instructions below for each function.
9.2 Adjusting the amount of froth
Turn the froth adjustment dial (D1) to adjust the amount of froth
on the milk delivered while making cappuccino and milk based
coffees.
Dial
position
Description
Recommended for…
No froth
CAFFELATTE/
MILK (hot milk)
Min. froth
LATTE MACCHIATO /
FLAT WHITE
Max. froth
CAPPUCCINO/
MILK (frothed milk)
9.3 Making cappuccino and milk based coffees
automatically
The control panel (B) has a button (B9) for automatically prepar-
ing
CAPPUCCINO
. Proceed as follows:
1. Fill the milk container (D) and attach it as described above.
2. Turn the froth adjustment dial (D1) on the milk container
lid (D2) to the position corresponding to the required froth.
3. Press the
CAPPUCCINO
button. The name of the drink
appears on the display (B4) together with a progress bar
which gradually fills as preparation progresses.
4. After a few seconds, frothed milk is delivered from the milk
spout (D5) into the cup below. Then the machine automat-
ically makes the coffee after delivering the milk.
9.4 Preparing “MILK MENU” drinks
Besides the drinks described above, the appliance automatically
prepares CAFFELATTE, LATTE MACCHIATO, FLAT WHITE and MILK
(hot milk).
To prepare one of these drinks, simply proceed as follows:
1. Fill the milk container (D) and attach it as described above;
2. Turn the froth adjustment dial (D1) on the milk container
lid (D2) to the position corresponding to the required froth;
3. Press the
MILK MENU
button (B10);
4. Press (B9) or (B10) (fig. 6) until the required drink
(CAFFELATTE, LATTE MACCHIATO, FLAT WHITE or MILK) ap-
pears on the display (B4);
5. Press the
OK
button (B3- fig. 7) to start delivery;
