21
37
38
When you install the filter, you must notify the appliance of its
presence.
8. Press (B6) to enter the "Settings" menu;
9. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines. Press
OK
;
10. Press the selection arrows until "Install filter" is displayed,
then press
OK
;
11. Confirm?": press
OK
;
12. "Hot water, Confirm?": Position a container under the hot
water spout (C6) (min. capacity: 500 ml), then press
OK
;
13. The appliance begins hot water delivery and the message
"Please wait" is displayed;
14. After the flow of hot water stops, the appliance automati-
cally resets to "Ready for coffee" status.
The filter is now active and you can use the coffee machine.
17.2 Replacing the filter
Replace the filter (C4) when "Replace filter, ESC to cancel, OK to
replace" appears on the display (B1). To replace immediately,
press
OK
(B3) and follow the instructions from point 8. To re-
place later, press ESC (B5). The symbol on the display reminds
you that the filter needs replacing.
To replace the filter, proceed as follows:
1. Extract the tank (A17) and exhausted filter;
2. Take the new filter out of its packet and proceed as illus-
trated in points 2, 3, 4, 5, 6 and 7 in the previous section;
3. Press
(B6) to enter the "Settings" menu;
4. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines. Press
OK
;
5. Press the selection arrows until "Replace filter" is dis-
played, then press
OK
;
6. Confirm?": press
OK
;
7. "Hot water, Confirm?": Position a container under the hot
water spout (C6) (min. capacity: 500 ml), then press
OK
;
8. The appliance begins hot water delivery and the message
"Please wait" is displayed;
9. After the flow of hot water stops, the appliance automati-
cally resets to "Ready for coffee" status.
The new filter is now active and you can use the coffee machine.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the filter even if
the message has not yet been displayed.
17.3 Removing the filter
If you want to use the appliance without the filter (C4), you
must remove it and notify the appliance of its removal. Proceed
as follows:
1. Extract the tank (A17) and exhausted filter;
2. Press
(B6) to enter the "Settings" menu;
3. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines. Press
OK
;
4. Press the selection arrows until "Remove filter" is dis-
played, then press
OK
;
5. "Confirm?": press
OK
to confirm removal. The appliance
goes back to the "Maintenance" menu;
Press /
ESC
(B5) to exit the menu.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the filter even if
the message has not yet been displayed.
18. TECHNICAL DATA
Voltage:
220-240 V~ 50/60 Hz max. 10A
Absorbed power:
1450W
Pressure:
1.5MPa (15 bars)
Max. water tank capacity:
1.8 l
Size LxDxH:
240x440x360 mm
Cord length:
1750 mm
Weight:
9.9 kg
Max. beans container capacity:
300 g
The appliance complies with the following EC
directives:
• EMC Directive 2004/108/EC and subsequent amendments;
• Materials and accessories coming into contact with food
conform to EEC regulation 1935/2004.
19. DISPOSING OF THE APPLIANCE
The appliance must not be disposed of with house-
hold waste, but taken to an authorised waste separa-
tion and recycling centre.
20. DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
REMEDY
Fill tank
Insufficient water in the tank (A17).
Fill the tank with water and/or insert it correct-
ly, pushing it as far as it will go until it clicks
into place (fig. 3B).
Insert tank
The tank (A17) is not correctly in place.
Insert the tank correctly and press as far as it
will go (page 3B).
Empty grounds container
The grounds container (A11) is full.
Empty the grounds container and drip tray
(A15), clean and replace. Important: when
removing the drip tray, the grounds contain-
er MUST be emptied, even if it contains few
grounds. If this is not done, when you make
the next coffees, the grounds container may fill
up more than expected and clog the machine.
Insert grounds container
After cleaning, the grounds container (A11)
has not been replaced.
Remove the drip tray (A15) and insert the
grounds container.
