13
Do not leave the appliance unattended while hot water is being
delivered.
1) To enable this function, press (B5). "RINSING" appears
on the display (B1);
2) After a few seconds, hot water is delivered first from the
coffee spouts, then from the hot water spout (if inserted)
to clean and heat the appliance’s internal circuit. A progress
bar is displayed and fills gradually as preparation proceeds;
3) To interrupt, press the arrow corresponding to "STOP" (B4).
Please note!
• If the appliance is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use;
• After cleaning, it is normal for the coffee grounds container
(A11) to contain water.
10. MAKING COFFEE
10.1 Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that the
coffee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding dial (A5) (fig. 7).
Please note:
The grinding adjustment dial must only be turned when the
coffee mill is in operation.
If the coffee is delivered too slowly or not
at all, turn one click clockwise towards 7.
For fuller bodied creamier coffee, turn
one click anticlockwise towards 1 (do not
turn more than one click at a time other-
wise the coffee could be delivered a drop
at a time).
These adjustments will only be evident after at least 2 cups of
coffee have been delivered. If this adjustment does not obtain
the desired result, turn the dial another click.
10.2 Tips for a hotter coffee
For hotter coffee, you should:
• to rinse, press /ESC (B5);
•
warm the cups with hot water using the hot water function
(see section “13. Delivering hot water”);
• increase the coffee temperature in the "Settings" menu
(see section “8.5 General”).
10.3 Making automatic recipes using coffee
beans
Important!
Do not use green, caramelised or candied coffee beans as they
could stick to the coffee mill and make it unusable.
1. Fill the container (A3) (fig. 8) with coffee beans;
2. Place under the coffee spouts (A9):
- 1 cup, if you want to make 1 coffee (fig. 9);
- 2 cups if you want 2 coffees.
3. Lower the spouts as near as possible to the cup. This makes
a creamier coffee (fig. 10);
4. Then select your required coffee:
Directly selected beverages
Recipe
Quantity Program-
mable
quantity
Default
aroma
Espresso (B8)
≃
40 ml
from
≃
30
to
≃
80ml
+
Coffee (B9)
≃
180 ml from
≃
100
to
≃
240cc
+
Long (B10)
≃
175 ml from
≃
115
to
≃
250cc
+
Beverages with coffee selectable from the
(B14)
Long Espresso
≃
120 ml from
≃
80
to
≃
180c
+
Short
≃
30 ml
from
≃
20
to
≃
40cc
+
≃
120 ml from
≃
80
to
≃
180cc
+
2 Espresso
≃
40 ml x
2 cups
--
+
2 Long
Espresso
≃
120 ml
x 2 cups
--
+
2 Short
Espresso
≃
30 ml x
2 cups
--
+
5. Preparation begins. A progress bar appears on the display
(B1) and gradually fills as preparation proceeds.
Please note:
• You can prepare 2 cups of SHORT ESPRESSO, ESPRESSO or
LONG ESPRESSO coffee at the same time by pressing "2X"
(B3) during preparation of single beverages (the image is
displayed for a few seconds at the start of preparation).
• Beep:
Use this function to enable or disable the beep. Proceed as
follows:
4. Press
OK
. The current state ("Enabled" or "Disabled") and
the operation to be performed ("Disable?" or "Enable?") is
displayed. Press
OK
to confirm;
5. Press
OK
to disable or enable the function.
The display goes back to the previous screen.
• Default beverages:
Use this function to reset the default values for all the beverag-
es, or the individual beverages programmed previously. Select
the beverage, then proceed as follows:
4. Select "All" to reset the aroma and quantity settings to the
default values, or select the required beverage, then press
OK
;
5. "Reset?": to reset the default values, press
OK
.
6. "Reset complete": the appliance confirms the reset and
goes back to the previous screen.
To reset another beverage, repeat from point 4 or to exit, press
/
ESC (B5).
• Default values:
Use this function to reset all the appliance and beverage settings
(apart from the language which remains as selected the first
time the appliance was used). Select the item, then proceed
as follows:
4. "Reset?"; press
OK
;
5. "Reset complete": the appliance confirms the reset and
goes back to the previous screen.
To exit, press /
ESC
(B5).
8.6 Statistics
This displays statistics relating to the machine. To display the
statistics, proceed as follows:
1. Press (B6) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "Statistics" is
displayed between the two lines;
3. Press
OK
(B3): statistics on the appliance are displayed, use
the selection arrows to scroll through the items;
4. Press
/
ESC
(B5) to exit.
To go back to the main screen, press /
ESC
.
9. RINSING
Use this function to deliver hot water from the coffee spouts
(A9) and hot water spout (C6), if inserted, to clean and heat the
appliance’s internal circuit.
Place a container with a minimum capacity of 100ml under the
coffee and hot water spouts.
Important! Danger of burns.
