13
order to prevent damaging the paint finish.
Fix the feet to the appliance with the nr. 4 screws 4.8x13 PH
G
supplied (see fig. 1), 2 screws for each foot.
Wall-Mounting Installation
The wall mounting kit contains:
4 metal brackets (
H
)
4 screws 4.5x25PH (
I
)
2 butterfly screws M5 (
J
)
4 plastic anchors 6x30 (
K
)
Required tools for assembly and estimated assembly
time
Drill
Screwdriver PH 2 x 100 (Phillips type)
Estimated assembly time: 30 minutes
Before installing the unit , make sure of the following:
-
The appliance must not be located directly
beneath a current outlet.
-
The plug and outlet must be easy to reach after
installation.
-
No electric cables or other pipes could be
damaged during the installation.
-
Keep away from curtains or flammable materials.
To wall-mount, proceed as follows:
Turn the appliance upside down on a flat stable surface. Fix
the 2 brackets
H
with the 2 butterfly screws
J
as shown in
Fig. 2. For brick walls use a 6 mm concrete drill bit. For plaster
board or drywall, it is recommended to use appropriate
screws and anchors (not supplied).
- Before drilling the wall, mark the exact points,
respecting the minimum distances as shown in fig. 3.
- Drill the wall where previously marked, and insert the
plastic anchors
K
.
- Fix the 2 metal brackets
H
using the two screws
I
provided.
- Hang the appliance on the bracket.
- Mark out the 2 lower fixing points. Remove the
appliance, drill the lower holes and insert the wall
anchors
K
.
- Now, you can hang back the heater on the bracket and
fix the lower part of the appliance with the 2 remaining
screws
I
.
USE
Operation and use
- Plug into the outlet socket.
- The appliance emits a beep. The power indicator light
(
A
) comes on and remains lit while the appliance is
powered.
- The appliance switches to stand-by.
- Press the ON/OFF (
B
) to turn the appliance on. It begins
heating the room according to the current settings.
- Press the MODE (
D
) button to select one of the following
operating modes:
-
Freeze prevention
In this mode, the appliance keeps the room at a
temperature of 45°F (7°C) to avoid freezing.
-
Heating 1, 2, 3 and Heating 3 + Fan
In this mode, the desired temperature can be selected by
pressing the adjustment b and –. By pushing
the + or - button once, the temperature (shown on the
display) will increase or decrease by 1 degree.
Heating 1
The appliance operates at low power.
Heating 2
The appliance operates at medium power.
Heating 3
The appliance operates at high power.
Heating 3 + Fan
The appliance operates at the maximum power with
the fan. The setting temperature range available is from
6
0
°F to 90°F (16°C to 32°C).
“
ECO plus” function
The
“
ECO plus” function is available in Heating 1, 2 3 and 3
+ fan modes only. To activate the function, press the
“
ECO
plus” (
E
) button.
When this function is active the appliance automatically sets
the most appropriate power level to guarantee optimum
comfort while reducing energy consumption. While the
“
ECO plus” function is active, the appliance may switch
automatically to a lower heating power than the one
displayed.
Working indicator
The symbol indicates the heating status by means of its
colors.
RED:
the unit is heating at the maximum power.
YELLOW:
the unit is heating at the medium power.
GREEN:
the unit is heating at the minimum power.
absent:
the unit is not heating.
Brightness of the display
The appliance allows two different brightness settings for the
display.
