20
DisplayeD messaGes
DisplayeD messaGe
possiBle cause
remeDy
FILL TANK
Insufficient water in the tank.
Fill the tank with water and/or insert it correctly, pushing it
as far as it will go until it clicks into place.
EMPTY GROUNDS CONTAINER
The grounds container (A22) is full.
Empty the grounds container and drip tray, clean and replace
(fig. 26).
Important: when removing the drip tray, the grounds contai-
ner must be emptied, even if it is not completely full.
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog
the machine.
GROUND TOO FINE ADJUST
MILL
alternating with
Insert water spout and press
OK
The grinding is too fine and the coffee is delivered too slowly
or not at all.
Repeat coffee delivery and turn the grinding adjustment
dial (fig. 12) one click clockwise towards “7” while the coffee
mill is in operation.
If after making at least 2 coffees delivery is still too slow,
repeat the correction procedure, turning the grinding
adjustment dial another click (see the section “adjusting the
coffee mill” on page 12).
INSERT GROUNDS CONTAINER
After cleaning, the grounds container has not been repla-
ced
Remove the drip tray and insert the grounds container.
ADD PRE-GROUNDCOFFEE
The “pre-ground coffee” function has been selected without
placing any pre-ground coffee in the funnel.
Place pre-ground coffee in the funnel (fig. 17) or deselect
the “pre-ground” function.
DESCALE!
The machine must be descaled.
The descaling procedure described in the "descaling" section
(page 17) needs to be performed as soon as possible.
LESS COFFEE
Too much coffee has been used.
Select a milder taste by pressing the
button (fig.
9) or reduce the quantity of pre-ground coffee, if using the
pre-ground function.
FILL BEANS CONTAINER
The coffee beans have run out.
Fll the beans container (fig. 13).
The pre-ground coffee funnel is clogged.
Clear the funnel with the help of a brush as described in the
section “Cleaning the pre-ground coffee funnel”.
INSERT INFUSER ASSEMBLY
The infuser has not been replaced after cleaning.
Insert the infuser as described in the section “cleaning the
infuser”.
INSERT TANK
The tank is not correctly in place.
Insert the tank correctly and press as far as it will go.
GENERAL ALARM
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly, as described in
the section “cleaning and maintenance”.
If the message is still displayed after cleaning, contact
De’Longhi Customer Experience.
EMPTY CIRCUIT FILL CIRCUIT
alternating with
Hot water press OK
The water circuit is empty
Connect the water spout (D3) (fig.6), fill the water tank and
press OK to deliver water from it, until it flows out normally.
REPLACE FILTER
The water filter is exhausted.
Replace the filter or remove it as described in the section
“Water filter”.
Press CLEAN
Milk has been delivered recently and the tubes inside the
milk container must be cleaned.
Press the CLEAN button (fig. 23) and keep it pressed until the
progress bar which appears on the display together with the
message “Cleaning underway “ is complete.
INSERT WATER SPOUT
The hot water spout is not inserted or is inserted incorrect-
ly.
Insert water spout (D3) as far as it will go.
INSERT MILK CONTAINER
The milk container is not inserted correctly.
Insert the milk container as far as it will go (fig. 21).
Summary of Contents for ECAM26455M
