background image

17

eXPlAnAtIon oF lIGhts

lIGht

PossIBle CAUse

ReMeDy

FlAshInG

Insufficient water in the tank� 

Fill the tank with water and insert it correctly, pushing it as 

far as it will go until it clicks into place� 

The tank is not correctly in place� 

Insert the tank correctly and press as far as it will go� 

FlAshInG

The grounds container (A13) is full� 

Empty the grounds container and drip tray, clean and 

replace�  Important: when removing the drip tray, the 

grounds container MUST be emptied, even if it contains 

few grounds� If this is not done, when you make the next 

coffees, the grounds container may fill up more than 

expected and clog the machine� 

After cleaning, the grounds container has 

not been replaced�

Remove the drip tray and insert the grounds container� 

FlAshInG

The grinding is too fine and the coffee is 

delivered too slowly or not at all�

Repeat coffee delivery and turn the grinding adjustment 

dial (fig. 13) one click clockwise towards “7” while the 

coffee mill is in operation� If after making at least 2 coffees 

delivery is still too slow, repeat the correction procedure, 

turning the grinding adjustment dial another click until 

delivery is correct (see the section: Adjusting the coffee mill 

on page 12)� If the problem persists, turn the steam dial to 

the I position and deliver water from the cappuccino maker�

 

FlAshInG

The "pre-ground coffee" function has been 

selected without placing any pre-ground 

coffee in the funnel�

Place pre-ground coffee in the funnel or deselect the 

"pre-ground" function� 

FlAshInG

The machine must be descaled� 

The descaling procedure described in the section 

“Descaling” needs to be performed as soon as possible.

FlAshInG

Too much coffee has been used�

Select a milder taste or reduce the quantity of pre-ground 

coffee then make the coffee again�

 

FlAshInG

The coffee beans have run out�

Fill the beans container�

The pre-ground coffee funnel is clogged�

Empty the funnel with the help of a knife�

Summary of Contents for ECAM 22.110















Reviews: