background image

34

• Press the                 button to set the auto-start time. (If you hold the            button down, the time is

changed rapidly).

• Press the                button to confirm the value;
• Press               once and the appliance displays the message: 

AUTO-START NO

Press the               button to modify the function (the appliance displays: 

AUTO-START Yes

)

• Press the        button to activate auto-start;

NOTE: 

when the appliance is turned off and auto-start time is set, the symbol         appears alongside the

time on the unlit display.
• Press the            button to exit programming mode or          to change other parameters.

16.3 Descale 

Over time, the continuous heating up of the water used to make the coffee leads to lime scale building up in
the inner circuits of the appliance.
When the appliance displays the message:  

DESCALE

you should perform the descale cycle.
Proceed as follows:
• make sure the appliance is ready. 
• press the          button (the light over the button comes on) then press the          button repeatedly until

the appliance displays: 

DESCALE No 

• Press             and the appliance displays the message: 

DESCALE Yes 

• Press the           button to start the descale programme.
• Empty the tank of water and pour in the contents of the bottle of descaler, then add half a litre of water.

For subsequent descaling, use descaler of the same type and brand as supplied (available from techni-
cal service centres authorised by the manufacturer).

• attach the water spout to the nozzle;
• place a container with a minimum capacity of 1.5 litres under the hot water spout (Fig. 3);
• press the [OK ]  button. Descaler runs off from the hot water spout into the container below. The applian-

ce displays: 

APPLIANCE IN    DESCALE

• the descale programme automatically performs a series of run offs and pauses to remove lime scale

deposits from inside the coffee maker.

•  After about 30 minutes, the appliance displays: 

RINSING  FILL TANK 

The appliance must now be rinsed through to eliminate residues of descaling solution from inside the applian-
ce. Proceed as follows:
•  empty the water tank, rinse and fill with clean water.
•  Reposition the tank.
•  Empty the full container and then put it back under the hot water spout.
•  Press the OK button. Hot water is run off from the spout into the container below and the appliance dis-

plays: 

Summary of Contents for EAM 3500 S

















Reviews: